816519
10
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
ENGLISHen
10
spindle is pushed in. This facilitates convenient
work. In order to enable automatic mode, briefly
press the trigger switch (3).
Note: The tool switches to sleep mode after 15
minutes without use. To activate again: press the
trigger switch (3) briefly.
Warning. Risk of injury from inadvertent
automatic machine start-up. In automatic
mode, do not touch any rotating parts such as
spindle, screwdriver bit or bit holder.
Impulse mode
Protruding screws can be precisely
countersunk using this function. Press
trigger switch (3) and countersink the screw with the
attached depth stop. To switch off release the
trigger switch.
7.3 Changing screwdriver bit
Prevent inadvertent starting: Set manual
mode and remove battery pack from the tool
before performing any retooling.
Inserting and removing the screwdriver bit:
See page 2, fig. 1.
- Remove the depth stop (11).
-Insert: Insert the screwdriver bit (12) in the bit
holder (13).
-Remove: Pull the screwdriver bit (12) from the bit
holder (13) using pliers.
- Attach the depth stop (11) again:
turn and engage in position when mounted.
Note: The bit holder (13) may be removed from the
spindle if the sleeve (15) is pulled back.
7.4 Working with depth stop
See page 2, fig. 2.
The depth of screw can be set by turning the setting
sleeve (17). On rotation of the knurled screw
corresponds to a drill depth of around 1.5 mm.
Adjust the setting sleeve (17) so that the screw
head is approx. 2 mm outside the stop sleeve (16)
when applying the screw.
Insert a screw as a test. Correct the screw depth if
necessary.
When screwing in crosshead screws, press
the machine with the screwdriver bit (12) firmly
against the screw until the screw is fully inserted;
otherwise the screwdriver bit could slip out of the
cross recess and damage the material.
.
8.1 Clean stiff depth stop
If the depth setting is stiff, the depth stop can be
dismantled without using tools. To do this, turn the
setting sleeve (17) clockwise until it becomes loose
from the union sleeve (18). Twist out the stop sleeve
(17) and clean thread.
Note: Only clean or vacuum mechanically. Do not
use oils or greases.
8.2 The machine's multifunctional
monitoring system
If the machine switches off automatically, the
machine electronics have activated automatic
protection mode.
In spite of this protective function, overloading
is still possible with certain applications and
can result in damage to the machine.
Causes and remedies:
1. Battery pack almost empty (the electronics
prevent the battery pack from discharging totally
and avoid irreparable damage).
If one LED (8) is flashing, the battery pack is
almost empty. If necessary, press the button (7)
and check the LED lamps (8) to see the charge
level. If the battery pack is almost empty, it must
be recharged.
2. Long continuous overloading of the machine will
activate the temperature cut-out.
Leave the machine or battery pack to cool.
Note: If the battery pack feels very warm, the
pack will cool more quickly in your "AIR
COOLED" charger.
Note: The machine will cool more quickly if you
operate it at idling speed.
3. If the current is too high (for example, if the
machine seizes continuously for long periods),
the machine switches off.
Switch off the machine at the trigger switch (3).
Then continue working as normal. Try to prevent
the machine from seizing.
ENG
Before carrying out any maintenance: remove the
battery pack from the machine.
Regularly remove and clean the depth stop (11).
See also chapter 8.1
Particles may become deposited inside the power
tool during operation. This impairs the cooling of the
power tool.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner. Prior to this operation,
separate the power tool from the power source and
wear protective goggles and a dust mask.
f
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
A Magazine screw attachment 630611000
B Screwdriver bits (length: 25 mm):
Recommendation: only use screwdriver bits
with plug-in ends of this type:
8. Troubleshooting
9. Maintenance
10. Accessories
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo TBS 18 LTX BL 5000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo TBS 18 LTX BL 5000 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 5.47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info