759251
10
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
ENGLISHen
10
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
See page 2.
1 Clamping lever for securing the saw blade
2 Saw blade support roller
3 Saw blade
4 Screw for adjusting the footplate
5 Footplate
6
Switch button
on the
chip blower
7 Adjustment lever for pendulum motion
8 Anti-splintering footplate insert
9Protective cap
10 Saw blade clamping fixture
11 Protective rod for preventing unintentional
contact with the saw blade
12 Setting wheel for speed adjustment
13 Trigger
14 Lock button for continuous activation
15
Handle
16 Hexagon spanner
17 Extractor connection piece
18 Curved support plate indicating preset cutting
angle
Before plugging in, check to see that the rated
mains voltage and mains frequency, as stated
on the rating label, match your power supply.
Never operate the machine without a saw
blade.
Australia: Always use a residual current device
(RCD) protected supply with a rated residual
current of 30 mA or less.
6.1 Fitting the anti-splintering footplate
insert
Danger of injury due to the sharp jigsaw blade.
Remove the saw blade
before fitting (8) the anti-
splintering footplate insert.
Turn the machine over so that the footplate faces
upwards. Insert the anti-splintering footplate from
the front,
ensuring the following:
The smooth side of the footplate faces upwards.
The slot is facing to the rear (towards the mains
cable).
If you wish to work with the protective plate attached
(see chapter Accessories 10.), fit the anti-splintering
footplate insert in the protective plate.
6.2 Inserting the saw blade
Danger of injury due to the sharp jigsaw blade.
After stopping work, the jigsaw blade may still
be hot. Wear protective gloves.
Use a saw blade that is suitable for the material
being sawn.
- Push the clamping lever (1) forwards up to the
stop and release (the clamping lever remains
open).
- Insert the saw blade (3) up to the stop. Ensure that
the saw teeth are facing forwards and the blade is
seated correctly in the groove on the saw blade
support roller (2).
- Push back the clamping lever (1) to its original
position (the saw blade is now clamped securely
in position).
6.3 Attaching / Removing the protective cap
Attachment: Push on the protective cap (9) from
the front until it engages
Removal: Grip both sides of the protective cap (9),
lift slightly, then pull forwards and remove.
6.4 Sawing with dust extraction
- Connect a suitable extraction device to the
extractor connection piece (17). Use a suction
hose with a 30 mm connector diameter.
- Attach the protective cap (9) for maximum
extraction efficiency.
- Switch off the chip blower (see chapter 7.1).
6.5 Sawing without dust extraction
- Work with the protective cap (9) removed
(see Removal chapter 6.3).
6.6 Diagonal cuts
Remove the protective cap (9), anti-splintering
footplate insert (8) and extraction hose. These parts
cannot be used for diagonal cuts.
- Slacken the screw (4).
- Slid the footplate (5) forwards slightly and turn.
- Then slide the footplate (5) forwards or backwards
and engage in one of the detents (the detents can
be viewed through the semicircular opening at the
rear of the footplate (5).) The preset angle is
indicated on the curved support plate (18) on the
footplate. Adjust to different angles using an angle
gage.
- Tighten the screw (4) again.
6.7 Sawing close to the wall
Remove the protective cap (9), anti-splintering
footplate insert (8), circular-cutting and parallel
guide. These parts cannot be used when sawing
close to the wall.
- Slacken the screw (4) until the footplate (5) can be
raised slightly.
- Raise the footplate (5) slightly and slide
backwards up to the stop.
5. Overview
6. Commissioning
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo STEB 80 Quick bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo STEB 80 Quick in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info