511032
14
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
14
ENGLISH
ENG
inside the drill chuck (if applicable / model-
specific). Caution left-handed thread !
(see Section 8.13.)
7.1 Side handle installation
For safety reasons, always use the side
handle supplied.
Open the clamping ring by turning the side handle
(16) counter-clockwise. Place the side handle onto
the machine's collar. Insert the depth stop (4).
Tighten the side handle in the required angle
depending on the task at hand.
8.1 Depth stop setting
Loosen the side handle (16). Set depth stop (4) to
the desired drilling depth and retighten the side
handle.
8.2 Switching on/off
To start the machine, press the trigger (13).
The speed can be changed at the trigger
(not SB 660).
Due to the electronic soft start the machine
accelerates continuously up to the pre-selected
speed (SBE 1010 Plus, SBE 85, SBE 850 Impuls,
SBE 850 Contact).
For continuous operation the trigger can be locked
with the lock button (11). To stop the machine,
press the trigger again.
If switched on continuously, the machine
continues running if it is jerked out of your
hands. Therefore, always hold the machine
with both hands on the handles, stand safely,
and concentrate on your work.
8.3 Speed preselection
(not for SB 660)
Pre-select the max. speed with the preselection
wheel (12). See page 4 for recommended drilling
speeds.
8.4 Gear selection
Select the desired gear by turning the control
knob (5).
Change gears only with the machine coming to a
complete standstill (start and switch right off
again).
1. gear
(low speed, high torque)
e.g. for screwing twist drilling
2. gear
(high speed) e.g. for twist drilling,
impact drilling
8.5 Changing between twist drilling/impact
drilling
Select desired operating mode by shifting the slide
switch (6) as required.
Twist drilling
Impact drilling
Use high speed for impact drilling. Set control
knob (5) to .
Impact and twist drilling can be done only with a
clockwise direction of rotation.
8.6 Selection of direction of rotation
(not for SB 660)
Do not actuate the rotation selector
switch (14) unless the motor has
completely stopped.
Select direction of rotation:
R = clockwise
L = counter-clockwise
The drill chuck must be firmly screwed
onto the spindle and the safety screw
inside the drill chuck (if applicable / model-
specific) must be firmly tightened with a
screwdriver. (Caution, left-handed thread !) If
rotated counterclockwise (e.g. when screwing)
it could otherwise become loose.
8.7 Tool change with Futuro Top keyless
chuck (3)
Insert tool. Grip the retaining ring (a) firmly and,
with the other hand, turn the sleeve (b) against the
stop. To open the drill chuck grip the retaining ring
8Use
b
a
17026951_0709 SB_Bauk.book Seite 14 Montag, 13. Juli 2009 1:54 13
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo SB 660 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo SB 660 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info