600615
9
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
ENGLISH en
9
Before plugging in, check to see that the rated
mains voltage and mains frequency,
as stated on the rating label, match your power
supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
Australia: Always use a residual current device
(RCD) protected supply with a rated residual
current of 30 mA or less.
6.1 Inserting / replacing the saw blade
Do not touch the saw blade immediately
following operation of the tool, as it can be
extremely hot and can lead to skin burns.
For access to the saw blade quick-clamping
device (2), it must be in its outermost position.
If required: press the trigger switch (7) lightly to
move the saw blade quick-clamping device into its
outermost position.
Pull the mains plug out of the socket.
For access to the saw blade quick-clamping
device (2), adjust the guide (1) if required.
1 Turn the clamping sleeve (3) in the direction
of the arrow and hold it.
2 Insert the saw blade as far as it will go or remove
it.
3 Release the clamping sleeve (3) (the clamping
sleeve rotates back to its original position).
4 Check that the saw blade is securely seated.
Note: Should it occur that a saw blade has broken
off and it cannot be removed by hand from the saw
blade quick-clamping device, turn the clamping
sleeve in the direction of the arrow and hold.
Engage the tip of a saw blade in the broken section
and pull it out. A fine-toothed metal saw blade is
best suited for this task. See Fig. A, page 2.
Note: Should it occur that, with the saw blade
inserted, the clamping sleeve cannot be turned:
move the saw blade upwards and downwards by
hand and simultaneously turn the clamping sleeve
in the direction of the arrow.
6.2 Setting the guide
The cutting depth can be limited by shifting the
guide (1) (e.g. when sawing in front of a wall).
Occasionally shift the guide (1) to achieve even
wear of the saw blade.
Release the clamping lever (4) and shift the guide
(1) along the length of the machine. Secure the
guide again using the clamping lever.
Note: If the guide is pulled out too far, the clamping
lever cannot be closed and locked for reasons
related to safety
S
ecure the guide firmly using the clamping
lever. The clamping lever must lock into place.
6.3 Pendulum action of the saw blade
The pendulum action of the saw blade increases the
sawing power (particularly in the case of soft
materials such as wood and plastics). Furthermore,
the pendulum action reduces the stress applied to
the saw blade, as it is raised when emerging from
the workpiece.
Use the rotary switch (6) to switch the pendulum
action on and off.
Pendulum action ON
Pendulum action OFF
For particularly exact sawing cuts and for
processing metals: switch off the pendulum action.
7.1 Switching on and off
To switch on: press the trigger switch (7).
To switch off: let go of the trigger switch (7).
7.2 Stepless stroke rate setting
The stroke rate can be changed steplessly by
varying the pressure applied to the trigger switch
(7), thus adapting it to the material and working
conditions.
7.3 Working Directions
Sawing:
Use a saw blade geared to the material to be sawn.
Depending on the use case, switch the pendulum
action on or off.
Press the machine with the guide (1) against the
workpiece. Switch on the machine, and only then
guide the saw blade against the workpiece.
Do not make contact with any objects or with the
ground with the moving saw blade (danger of
recoil!)
Adapt the stroke rate to the material to the sawn.
Avoid excessive pressure on the saw blade
(particularly in the case of long saw blades).
If the saw blade jams, turn the machine off
immediately. Widen the sawn gap slightly with a
suitable tool and take out the machine.
After completing the sawing cut, switch off the
machine and only take it out of the sawn gap to
place it down once the saw blade has come to a
standstill (danger of recoil).
Plunge cuts:
Plunge cuts may only be made in soft materials
such as wood or plastic. Only use short saw blades.
Hold the machine with both hands at the intended
handles, take a secure stance and concentrate on
the work.
See Fig. B, page 2. The machine is pressed with the
edge of the guide (1) against the workpiece. The
saw blade does not make contact with the
workpiece. Switch on the machine. The corner of
the guide serves as a pivot point around which the
machine is slowly aligned, whereby the saw blade
cuts into the workpiece.
6. Initial Operation, Setting
7. Use
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo PSE 1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo PSE 1200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info