625640
11
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
ENGLISH en
11
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
See page 2.
1 Additional handle *
2 Wing screw (for adjusting the depth stop) *
3Depth stop *
4Clamping knob *
5 Bar handle (additional handle) *
6 Dust protection cap
7Tool lock
8Knob
9 Metabo VibraTech (MVT): integrated damping
system
10 Locking lever (to release the continuous
operation) *
11 Trigger
12 Handle
13 Adjustment wheel
14 Overloading and service display
15 Mode display
* equipment-specific
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Use only extension cables with a minimum cross-
section of 1.5 mm
2
. Extension cables must
correspond to the power consumption of the
machine (cf Technical Specifications). If a cable
roller is used, always roll up the cable completely.
6.1 Assembly of the bow handle or
additional handle
For safety reasons, always use the bow
handle (5) or additional handle (1) supplied.
MHE 5:
Release the clamping ring by turning the clamping
knob (4) anticlockwise. Adjust the bow handle (5) to
the required position and angle. Tighten the
clamping knob firmly.
KHE 5-40:
Open the clamping ring by turning the additional
handle (1) anticlockwise. Secure the additional
handle at the required angle. Tighten the additional
handle.
7.1 Depth Stop Setting
(only for KHE 5-40)
Release the wing (2) screw. Set the depth stop (3)
to the required drilling depth. Retighten the wing
screw (2).
7.2 Positioning, removing tool
Before inserting, clean tool shank and apply
supplied special grease (accessories: Order
no. 6.31800)! Use only SDS-max tools.
The dust protection cap (6) prevents the
ingress of drilling dust during operation. When
inserting the tool, pay attention to ensure that the
dust protection cap (6) is not damaged.
Positioning tool:
Hold the tool lock (7) in the front position when
inserting the tool. Turn tool and insert until it
engages. The tool is being locked.
Pull on the tool to check that it is correctly
seated. (It must be possible to move the tool a
few centimetres in an axial direction.)
Remove the tool:
Pull the tool lock (7) backwards in direction
indicated by arrow (a) and remove tool (b). See
page 3.
7.3 Setting operating mode and chisel
position
Avoid levering with the machine when a chisel
is fitted.
KHE 5-40:
Do not activate the switch button (8) until the
motor has completely stopped.
Only rotate the switch button (8) in the
direction of the arrow.
Turn the switch button (8) to select the desired
operating mode.
Hammer drilling
Chiselling
Setting the position of the chisel:
The chisel can be
locked in different positions.
- Insert the chisel.
- Turn the switch button (8) to the intermediate
position (between setting and setting ).
- Turn the chisel to the required position.
- Turn the switch button (8) to position .
- Turn the chisel until it engages.
When a chisel is fitted, only operate the
machine in the chiselling operating mode .
MHE 5:
Only operate the switch button (8) when the
motor is at a standstill.
Chiselling
5. Overview
6. Commissioning
7. Use
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo MHE 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo MHE 5 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 7,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info