595085
16
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
16
ENGLISH
ENG
General notes:
- Centre the position at which the hole is to be
drilled.
- Note: If the display (24) is switching from red to
green (see diagram, page 3), a small amount of
holding power is available, which can be used
when fastening and aligning the magnetic drill
stand.
- Align the magnetic drill stand so that the drill bit
is above the centre marking.
- Fully activate the magnet in the magnetic drill
stand.
- Pull out the lock switch (6).
- Finally, switch on the driving unit (move the
switch (8) to the "I" position).
- If necessary, switch on the cooling lubrication
unit (see chapter 7.2.
- Start the drilling operation with minimum feeding
force. When the drill bit has started to drill,
slightly higher feeding force can be applied.
Excessive feeding force leads to premature wear
of the drill bit. Ensure that the chip flow is regular
- Use a wire hook
to remove the chips.
- If the drilled metal piece is not automatically
ejected by the core drill bit: remove it using a
tool.
Special notes on tools with morse taper shank
MK2:
Inserting
tool
:
To prevent the driving unit from
moving up/
down accidentally
: depress the lock switch
(6).
The tool is only guaranteed to fit perfectly in
the drill spindle (13) if the female taper of the
drill spindle and the taper shank of the tool are free
of dirt and grease.
Caution! Never use excessive force to press
tools into the female taper of the drill spindle!
Always use sharp tools in perfect condition.
Switch off the machine. Remove battery
pack from machine.
Tools with a taper shank MK2 can be used directly
in the female taper of the drill spindle (13).
Driving out
the tool:
Insert the removal tool (12) - with the sloping edge
against the tool - in the slot (11) on the machine
neck. If the removal tool cannot be inserted
through the drill spindle, you should turn the drill
spindle (13) slightly by hand. Drive out the tool by
knocking lightly on the removal tool with a hammer
(12).
Special notes on tools with Weldon shank
19 mm:
To prevent the driving unit from
moving up/
down accidentally
: depress the lock switch
(6).
First, insert the industrial holder 6.26602 (see
Chapter 10 Accessories).
When inserting the attachment, ensure that
the side pin of the industrial attachment
engages with the anti-twist device (14).
(17)Then connect the quick-action coupling from
the c
ooling lubrication unit to the connecting
piece on the industrial attachment
6.26602.
Inserting the
tool
:
- Insert the centring pin for the core drill bit (see
chapter 10 Accessories) in the tool.
- Insert the tool in the tool holder (16) so that both
surfaces (on the cylindrical part of the tool) are
located at the positions of the threaded pins (15).
- Guide the tool upwards as far as it will go
(against the pressure of the integral spring) and
tighten the threaded pins (15) using the Allen key.
Removing
the tool
:
- Release the two threaded pins (15).
Perform regular maintenance work, cleaning and
lubrication.
Remove the battery pack from the machine before
any adjustments, conversions or servicing are
performed.
To lubricate the rack and pinion that moves the
slide plate (7) up and down, you should occasion-
ally apply some multi-purpose grease to the rack.
Coat the sliding surfaces of the slide plate (7) with
multi-purpose grease.
Occasionally apply a drop of machine oil to the
area where the shaft penetrates (23) the magnet
section.
To prevent rust, occasionally rub the magnet block
with a cloth soaked in oil.
Backlash of the slide plate
The backlash of the side plate is set ex works.
The side plate (7) must be adjusted so that it can
still be moved freely up and down (when the
driving unit is installed), and so that it will remain in
any position without the weight of the driving unit
pulling it down.
If necessary, you can adjust the backlash of the
slide plate (7) using the three threaded pins (5):
release the counternuts, tighten the threaded pins
and fasten the counternuts again.
8 Cleaning, Maintenance
17027057_0211 MAG 28 LTX 32.book Seite 16 Dienstag, 1. März 2011 1:15 13
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo MAG 28 LTX 32 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo MAG 28 LTX 32 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info