595135
12
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
12
ENGLISH
ENG
Impact drilling:
- Extremely high torques are produced
when the drill seizes. Therefore for safety
reasons, always use the additional handle (6)
supplied.
- Do not hold the machine by the bow handle (1)
if there is a danger of the machine seizing.
There is a risk of injury to the user.
Option 1
Pull the bow handle (1) backwards parallel to the
housing and tighten clamping knob. Screw the
additional handle (6) into one of the front threads
(2) (left and right of the gear housing) and tighten
by hand.
Option 2
Upright working position for reduced stress on the
back when working on floors
:
The additional handle (6) can also be attached to
the motor housing. Screw the additional handle
into the rear thread (7) and tighten by hand.
8.1 Attaching and removing tools
Before fitting tools, clean shank and apply
special grease enclosed with tool (acces-
sories order no. 6.31800)! Use only SDS-max
tools.
Attaching tools:
Turn tool and insert until it engages. The tool is
automatically locked.
Pull on the tool to check that it is seated
correctly.
(It must be possible to move the
tool a few centimetres in an axial direction.)
Removing the tool:
Pull tool lock (4) backwards in direction indicated
by arrow (a) and remove tool (b).
8.2 Setting the operating mode
Turn the switch button (5) to select the desired
operating mode.
Hammer drilling (only for KHE 96)
Chiselling
When a chisel is fitted, only operate the
machine in the chiselling operating
mode .
8.3 Adjusting the chisel position
The chisel can be secured in 16 different positions.
- Insert the chisel.
- Turn the switch button (5) to position .
- Turn the chisel to the required position.
- Turn the switch button (5) to position .
- Turn the chisel until it engages.
When a chisel is fitted, only operate the
machine in the chiselling operating
mode .
8.4 Setting the impact force and speed
Turn the adjusting wheel to the desired letter.
The correct setting depends on the task in hand.
Example: set the switch to "A" or "B" (low impact
force) when chiselling soft, brittle material or trying
to minimise break-off.
Set the wheel to the letter "G" (high performance)
when breaking off or drilling harder materials.
8.5 Switching On and Off
Instantaneous activation:
To start the machine, press the trigger switch (9).
Release the trigger (9) to switch off.
Continuous operation:
For continuous operation the trigger switch can be
locked using the lock button (10).
Press and release the trigger (9) again to switch off.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine
with both hands using the handles provided,
stand in a safe position and concentrate.
8.6 Metabo VibraTech (MVT)
For reduced vibrations and less stress on the
hands.
Always apply a moderate amount of pressure to
the handle when pushing down the machine and
do not force. Vibrations are reduced most effec-
tively at the central position (8).
Motor cleaning: blow out the machine thoroughly
at regular intervals through the air slots with
compressed air.
Only moderate pressure is required when working
with the machine. Applying excessive pressure
does not increase your working performance and
may decrease the service life of your machine.
8Use
9 Cleaning, Maintenance
10 Tips and Tricks
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo KHE 96 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo KHE 96 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info