625642
11
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
ENGLISH
11
ENG
8.4 Setting chisel position
The Chisel can be locked in 8 different positions.
Insert the chisel.
Press the lock (3) and hold in.
Turn the switch button (2) until it points upwards
(between position and ). Let go of the
lock.
Turn the chisel in the direction of the arrow until it
is in the desired position.
Press the lock (3) and hold in.
Turn the switch button (2) to position .
Release the lock (3) and check that the switch
button (2) has engaged.
Turn the chisel in the direction of the arrow until it
engages.
When a chisel is fitted, only operate the
machine in the chiselling operating
mode.
8.5 Setting impact force and speed
Turn the adjusting wheel (8) to the desired value.
The higher the number, the greater the speed and
the higher the impact force.
The correct setting is found by trial and error.
Example: if soft, brittle materials are being
chiselled, or cracking is to be kept to a minimum,
set the adjusting wheel to "1“ to "2“ (low impact
force).
For demolition or for drilling into harder materials,
set the adjusting wheel to the highest number
(max.power).
8.6 Switching On and Off
To switch on:
press the trigger switch (5).
To switch off:
release the trigger switch (5).
When working with the chisel hammer, only a
moderate amount of press-on pressure (approx.
20 kg) is required. High press-on pressure does
not increase work capacity and can possibly
shorten the service life of your tool.
In the case of deep bores, pull the drill bit out of the
bore from time to time in order to remove the stone
dust.
Motor cleaning: blow out the machine regularly
and thoroughly through the air slots with
compressed air.
Electronic signal indicator (6):
Rapid flashing - CODE! System
The tool was locked with a CODE! Key. The elec-
tronic anti-theft device is active. The tool can be
unlocked again with a CODE! key.
Slow flashing - carbon brushes worn (only KHE 75)
The carbon brushes are almost completely worn. If
the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorised service centre.
Continuous light - Service call-up
The tool cut out automatically. Bring the tool to a
Metabo Service Centre.
Rotational speed fluctuations:
High-energy, high-frequency interference can
cause rotational speed fluctuations up to the
maximum idling speed. The fluctuations disappear
again as soon as the interference fades away.
Use only genuine Metabo accessories.
If you need any accessories, check with your dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4:
A Extensive range of chisels for a wide variety of
applications.
B Special grease (for lubricating the tool shanks)
CCODE! key
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Any Metabo power tool in need of repair can be
sent to one of the addresses listed in the spare
parts list.
Please enclose a description of the fault with the
power tool.
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that
can be recycled.
These instructions are printed on chlorine-free
bleached paper.
9 Tips and Tricks
10 Maintenance
11 Troubleshooting
12 Accessories
13 Repairs
14 Environmental Protection
17026726_0107 KHE 75 KHE 55.book Seite 11 Freitag, 26. Januar 2007 8:42 08
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo KHE 75 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo KHE 75 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info