648371
17
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
ENGLISH en
17
12.Push on the outer flange (41) - The flat side
must point towards the tensioning screw with
washer (40)!
13.Put on the tensioning screw with the washer
(40) in anti-clockwise direction (left-hand
thread) and tighten by hand.
14.Lock saw blade: press the locking button (15)
and turn the saw blade with the other hand
until the locking button engages. Hold down
the locking button.
Danger!
Do not extend the hexagon wrench.
Do not tighten the tensioning screw by hitting
the hexagon wrench.
15.Firmly tighten the tensioning screw (40) using
the hexagon wrench (17).
16.Check function. Loosen the safety lock (29)
and fold the saw downwards:
when folding down the retractable blade
guard, it has to provide free access to the saw
blade without touching other parts.
When folding the saw upwards into the
starting position, the retractable blade guard
has to cover the saw blade automatically.
– Rotate the saw blade manually. You should be
able to rotate the saw blade into any possible
position without touching other parts.
10.2 Table insert change
Danger!
With a damaged table insert (20) there is a risk of
small parts getting stuck between table insert and
saw blade, blocking the saw blade. Replace
damaged table inserts immediately!
1. Remove screws at table insert. If required,
rotate turntable and incline saw head to be
able to reach the screws.
2. Remove table insert.
3. Insert new table insert.
4. Tighten the screws at the table insert.
10.3 Adjust parallel guide/ripping fence
1. Loosen Allen screws (46).
2. Adjust the parallel guide/ripping fence (30) in
such a way that it is exactly perpendicular to
the saw blade when the turntable engages in
the 0° position.
3. Tighten the Allen screws (46).
10.4 Adjust the cutting laser
Danger!
LASER BEAM
DO NOT LOOK INTO THE BEAM
You will need a 2.5 mm hexagon wrench for the
adjustment. Place a board with a vertical line at the
parallel guide/ripping fence to see the laser beam
better.
1. Twist the screw (38), thus setting the laser
beam parallel to the saw blade (42).
2. Twist the screw (37) OR (39), thus setting the
laser beam parallel to the saw blade (42) .
3. Twist the screw (37) AND (39), thus adjusting
the clearance to the saw blade (42)
4. Repeat steps 1 to 3 if required.
10.5 Cleaning the device
Remove chips and saw dust with vacuum cleaner
or brush from:
adjustment installations
–controls;
– motor vent slots;
space under table insert;
space under turntable (accessible through
openings on the rear);
cutting laser;
Cutting line illumination
10.6 Storage of device
Danger!
Store the device in such a way that it cannot be
put into operation by unauthorised personnel.
Ensure that the stationary device cannot cause
injury.
Caution!
Do not store the tool outdoors or in damp
conditions without protection.
10.7 Maintenance
Prior to each use
Remove saw chips with vacuum or brush.
Check power cable and power cable plug for
damage; if necessary have damaged parts
replaced by a qualified electrician.
Check all movable parts if they can be moved
freely across the entire range of movement.
Check whether that retractable blade guard (7)
works correctly and does not stick. When
folding down, it has to provide free access to the
saw blade without touching other parts. When
folding the saw upwards into the starting
position, it must cover the saw blade
automatically. If damaged or not functioning
correctly, have the device repaired before using.
Regularly, depending on conditions of use
Check all screwed joints, retighten if necessary.
Check reset function of the saw head (saw head
has to return to the upper starting position by
means of spring force), if required have spring
replaced.
Slightly oil guide elements.
Use appropriate supports on the left and right of
the saw for long workpieces.
When cutting small pieces, use additional guide
(a suitable wooden board attached with screws
to the guide of the device, can be used as
additional guide).
When cutting a curved (contorted) board (49)
place the convex side at the parallel guide/
ripping fence.
– Do not cut workpiece upright, but flat on the
turntable.
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
A Spray for maintenance and care for the
removal of resin residues and to preserve the
metal surfaces: 0911018691
B Metabo all-purpose vacuum cleaner (see
catalogue)
C Stands:
Universal machine stand UMS: 6.31317
Machine stand KSU 251: 6.29005
Machine stand KSU 401: 6.29006
D Saw blade Power Cut: 6.28009
216 × 2.4 / 1.8 × 30 24 WZ 5° neg
For good cutting results for longitudinal and cross
cuts in solid wood
E Saw blade Precision Cut Classic 6.28060
216 × 2.4 / 1.8 × 30 40 WZ 5° neg
For good cutting results for longitudinal and cross
cuts in solid wood and chipboard
F Saw blade Multi Cut Classic: 6.28066
216 × 2.4 / 1.8 × 30 60 FZ/TZ 5° neg
For good cutting results with longitudinal and
cross cuts in coated materials, laminate, plastic
and aluminium profiles
G Saw blade Precision Cut: 6.28041
216 x 2.4 x 30 48 WZ 5°neg for very good cutting
results with longitudinal and cross cuts in solid
wood
H Saw blade Multi Cut: 6.28083
216 x 2.4 x 30 60 FZ/TZ 5° neg for very good
cutting results in coated materials, laminate,
plastic and aluminium profiles
For a complete range of accessories, see
www.metabo.com or the catalogue.
Danger!
Repair of power tools must be carried out by
qualified electricians only!
If the mains connection lead of this device is
damaged, it must be replaced with an original
Metabo mains connection lead.
If you have Metabo power tools that require
repairs, please contact your Metabo service
centre. See www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! Used
power tools must be collected separately
and handed in for environmentally compatible
recycling in accordance with European Directive
2002/96/EC on waste electrical and electronic
equipment and its implementation in national
legal systems.
Following you will find a description of problems
and faults that you may remedy yourself. If the
corrective measures described here do not help,
kindly refer to chapter 13. "Repairs".
Danger!
There are particularly many accidents in
connection with problems and faults. Therefore
keep in mind:
Disconnect the mains plug prior to any fault
service.
Check that all safety devices are operational
again after each fault service.
No trimming function
Transport lock activated:
pull out transport lock.
Safety lock activated:
loosen safety lock.
Cutting power too low
Saw blade blunt (possibly tempering marks on
blade body);
Saw blade unsuitable for the material (see
chapter 12. "Accessories");
Saw blade contorted:
Replace saw blade (see chapter 10.
"Maintenance").
Saw vibrates a lot
Saw blade contorted:
Replace saw blade (see chapter 10.
"Maintenance").
Saw blade not installed properly:
Install saw blade properly (see chapter 10.
"Maintenance").
Turntable hard to turn
Chips under turntable:
remove chips.
KGSV 72 Xact SYM: Angle setting hard to
effect when moving the table halves (9)
Chips under turntable:
remove chips. The space under the turntable is
accessible through openings on the rear
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U=mains voltage
11. Tips and Tricks
12. Accessories
13. Repairs
14. Environmental Protection
15. Troubleshooting
16. Technical Specifications
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo KGSV 72 Xact bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo KGSV 72 Xact in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 31,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info