600820
9
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
ENGLISH en
9
Pump clogged or defective.
- Disassemble and clean pump. Clean diffuser,
replace if necessary. Clean impeller, replace
if necessary. See section 11.
9.2 Pump not drawing in correctly or run-
ning very loudly:
Insufficient water.
- Ensure there is a sufficient water supply.
Pump not sufficiently filled with water.
- See section 6.7.
Suction line leaking.
- Seal suction line, tighten screw-couplings.
Suction height too high.
- Observe maximum suction height.
- Insert check valve, fill suction line with water.
Intake filter (accessories) obstructed.
- Clean, replace if necessary.
Check valve (accessories) blocked.
- Clean, replace if necessary.
Water discharge between motor and pump,
shaft seal leaking. (Minor discharge of water
(max. approx. 30 drops per day) is normal with
the use of shaft seals).
- Replace shaft seal. See section 11.
Pump clogged or defective.
- See section 9.1.
9.3 Pressure too low or pump runs continu-
ously:
Suction line leaking or suction height too high.
- See section 9.2.
Pump clogged or defective.
- See section 9.1.
HWW...: Pressure switch incorrectly adjusted.
- Read off switch-on and switch-off pressure at
the pressure gauge (3) and check values (see
section 13 Technical Specifications). If an
adaptation is necessary, please contact
Metabo Customer Service. See section 11.
HWW...: Pump starts up even after removal of
small volume of water (approx. 0.5 l).
- Check whether the pilot pressure in the pres-
sure vessel is too low. Increase pressure if
necessary. See section 9.4.
HWW...: Water is running out of the air valve.
- Rubber bellows in pressure vessel leaking,
replace it. See section 11.
9.4 Increasing pilot pressure (only HWW...)
If – in the course of time – the pump starts up even
after the removal of a small volume of water
(approx. 0.5 l), the pilot pressure in the vessel must
be restored.
Note:
The pilot pressure cannot be read off at the
pressure gauge (3).
1. Unplug mains cable.
2. Open the discharge line (open water tap or
spray nozzle), allow water to drain off
completely.
3. Unscrew plastic cap on front face of pressure
vessel; the air valve is located behind it.
4. Mount air pump or compressor hose with a
"tyre valve" connection and pressure gauge on
the air valve.
5. Pump up to the specified pilot pressure (see
section 13. Technical Specifications).
6. Connect device again and check operation.
f
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Danger! Repairs to this device must be
carried out by qualified electricians only!
If you have Metabo devices that require repairs,
please contact your Metabo service centre. For
addresses see www.metabo.com.
For shipment: drain pump and vessel completely
(see section 8.3).
You can download spare parts lists from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recy-
cling.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
The pump characteristic curve (diagram on page
3) shows the conveying capacity that can be
reached depending on the conveying height
(suction height 0.5 m and 1" suction hose).
U =Mains voltage
f=Frequency
P
1
=Rated power
I =Rated current
C=Operating condenser
n =Rated speed
F
V,max
=max. conveying capacity
F
h,max
=max. conveying height
F
p,max
=max. conveying pressure
p
1
=Pressure switch: switch-on pressure
p
2
=Pressure switch: switch-off pressure
S
h,max
=max. suction height
S
temp
=max. supply temperature
T
temp
=Ambient temperature
S
1
=Splash protection class
S
2
=Protection class
S
3
=Insulation class
M
P
=Pump housing material
G=Grey cast iron
M
R
=Pump shaft material
M
W
=Pump impeller material
D
s
=Suction connection female thread
D
p
=Pressure connection female thread
T
V
=Pressure vessel volume
T
p,max
=max. vessel pressure
T
p,1
=Vessel pilot pressure
A =Dimensions:
Length x Width x Height
m =Weight (with mains cable)
~ Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this power tool and compare these
with the values emitted by other power tools. The
actual values may be higher or lower, depending
on the particular application and the condition of
the tool or power tool. In estimating the values, you
should also include work breaks and periods of low
use. Based on the estimated emission values,
specify protective measures for the user - for
example, any organisational steps that must be put
in place.
Typical A-effective perceived sound levels:
:
L
pA
=Sound pressure level
L
WA
=Acoustic power level
K
pA
, K
WA
= Uncertainty
L
WA(G)
=Guaranteed acoustic power level as per
2000/14/EC
Wear ear protectors!
10. Accessories
11. Repairs
12. Environmental Protection
13. Technical specifications
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo HWW 9000-100 G bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo HWW 9000-100 G in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info