451403
22
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
- REMOVE ALL ADJUSTING KEYS AND WRECHES: From habit of checking to see that all keys and adjusting wrenches
are removed from tool before switchine in "ON".
- ALWAYS USE SAW BLADE GUARD AND RIVING KNIFE for every operation for which they can be used, including through
sawing. Through sawing operations are those when the blade cuts completely through the work piece as in ripping or cross
cutting.
- ALWAYS HOLD WORK FIRMLY AGAINST RIP FENCE OR MITRE FENCE.
- USE PUSH-STICK if distance between blade and rip fence is less than 120 mm/5".
- NEVER PERFORM ANY OPERATION "FREE-HAND".
- NEVER REACH BEHIND, OVER OR UNDER THE CUTTING TOOL WITH EITHER HAND FOR ANY REASON. Keep
hands away from saw blade; do not reach into area 120 mm left and right of saw blade.
- DIRECTION OF FEED: Feed work into saw blade against direction of rotation only.
- AVOID KICKBACKS (work thrown back at you) by keeping the rip fence parallel to the blade, keeping riving knife and guards
in place and operating, by not releasing work before it is pushed all the way past the saw blade, and by not ripping stock
that is twisted or warped or does not have a straight edge to guide along the fence.
12.1 Problems
- If saw blade is stalled by waste, or the discharge port of the chip case clogged, switch machine off and let blade come to
a complete standstill before attempting to remove obstruction.
- Switch motor off immediately if blade has stalled. A dull blade is most often the cause for what appears to be a loss of
power of the motor.
- An extremely dull blade leaves burn marks in the kerf. Replace or resharpen at once.
- After a power failure the machine has to be switched on again.
13 Care and Maintenance
- Always disconnect from power before servicing. Do not rely on switch alone.
- This machine requires very little maintenance.
- When changing the saw blade apply a light coat of oil to the arbor bolt.
- Regularly apply a light coat of oil to the mitre fence guide rod.
13.1 Tool maintenance
Residue resin built-up on the saw blade(s) should be removed regularly. Immerse blade in a natrium carbonate solution or in
paraffin/kerosene or mineral turpentine for 24 hours. The residue resin is then easily wiped off with a rag.
Clean and sharp saw blades improve the quality of the cuts and cutting efficiency.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo BKH 400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo BKH 400 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 6,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info