595146
10
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
ENGLISHen
10
screwdriver to firmly tighten the safety screw inside
the drill chuck (if applicable / model-specific).
Caution left-handed thread !
(see Section 8.7.)
6.1 Assembly of additional handle (2)
For safety reasons, always use the additional
handle supplied.
Open the clamping ring by turning the
additional
handle (2) counter-clockwise. Push the additiona
l
handle onto the collar of the machine. Slide the
additional handle far enough forward so that it can
be turned. At the desired angle, pull it back and
tighten firmly.
7. Use
7.1 Setting direction of rotation,
transport lock (switch-on lock)
Do not activate the rotation selector switch (7)
unless the motor has completely stopped.
See page 2.
R =
Clockwise setting
L =
Counter-clockwise setting
0 =
Central position: transport lock setting
(switch-on lock)
The drill chuck must be firmly screwed onto
the spindle and the safety screw inside the drill
chuck (if applicable / model-specific) must be firmly
tightened with a screwdriver. (Caution, left-handed
thread !) If rotated counterclockwise (e.g. when
screwing) it could otherwise become loose.
7.2 Selecting a gear
Select the desired gear by turning the
thumbwheel (1).
Change speed only when the machine
is in the process of running down
(briefly switch it on and off).
1st gear (low speed, high torque)
e.g. for screwdriving, drilling
2nd gear (high speed) e.g. for drilling
7.3 Preselect speed
Use the setting wheel (5) to preselect the maximum
speed. See page 4 for r
ecommended drilling
speeds.
7.4 Switching on/off, changing speed
Switching on, speed: pres
s the trigger (9).
The speed can be changed by pressing in the
trigger.
The electronic soft start means that the ma
chine
accelerates continuously until the preselected
speed is reached.
Release the trigger to switch off.
Continuous activation: Wh
ile pressing on the
trigger (9), press in the locking button (8) and
then release the trigger. To sw
itch off, press and
release the trigger (9) again.
In continuous operation, the machine
continues running if it is forced out of your
hands
. Therefore, always hold the machine with
both hands using the handles provided, stand in
a safe position and concentrate.
7.5 Tool change with
Plus (4)
chuck
See illustrations A, page 2.
Opening the drill chuck:
Using one hand, hold the retaining ring securely
(depending on
equipment, not necessary for
BE 1300 Quick) and, using the other hand, turn the
sleeve in the direction of the arrow -1.
The ratchet sound which can possibly be heard
after op
ening the drill chuck is functional and is
switched off by a reverse rotation of the sleeve.
BE 751, BE 1100: If the chuck is very securely tight-
ened: Unplug. Hold the chuck using an open-end
spanner at the flats on its head, and turn the sleeve
vigorously in the direction of the arrow -1.
Clamping the tool
- Insert the tool -2- as far as possible.
- Using one hand, hold the retainer ring securely
(depen
ding on equipment; not required for
BE 1300 Quick).
- Turn sleeve in direction -3- until the noticeable
mechanical
resistance has been overcome.
- Caut
ion! The tool is not yet fully tightened!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further - only
now is the tool safely clamped.
With a soft tool shank, retigh
tening may be required
after a short period of operation.
7.6 Tool change with a geared chuck (3)
See illustrations B on page 2.
Opening the drill chuck: O
pen the geared chuck
with chuck key -1.
Clamping the tool: I
nsert tool -2- as far as possible
and, using the chuck key, evenly secure in all 3
bores -3.
7.7 Drill chuck with "Quick" change system
(for
BE 1300 Quick)
See illustration on page 2.
To remove: Push the interlock ring forward (a),
advance and pull off the chuck (b).
To mount: Pus
h the interlock ring forward and
move the chuck as far as the limit stop on the drill
spindle (slightly turn the chuck if necessary).
7.8 Unscrewing chuck (when screwing with-
out chuck or when using attachments)
See illustrations Y, Z on the second last page.
Note for illus. Y, Z: Release by tapping lightly with a
rubber hammer, as shown, and unscrew.
Note: If a bit clamping bush (order no. 6.31281) is
attached, the screwdriver bit inserted in the
hexagon socket of the spindle is held in place.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo BE 1100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo BE 1100 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info