451401
20
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
20
ENGLISH
prior to every cutting operation, to
accommodate the height of the
workpiece (the upper blade guide
should be set approx. 3 mm above
the workpiece);
after adjustments of band saw blade
or saw table (e.g. band saw blade
change, tensioning of the band saw
blade, saw table alignment).
A
Danger!
Turn the machine OFF and wait
for the band saw blade to stop before
adjusting the upper blade guide or
the saw table.
1. Set the upper blade guide (53) with
the setting knob (54) to the desired
height.
8.2 Sawing
1. If necessary, adjust the table tilt.
2. Select rip fence and table tilt for the
type of cutting operation to be car-
ried out.
A
Hazard generated by a jam-
ming workpiece!
When sawing with the rip fence and a
tilted saw table, the rip fence must be
installed on that side of the saw table
which is tilted downward.
3. Set upper blade guide 3 mm above
the workpiece.
3
Note:
Always make a trial cut in a piece
of scrap to verify settings; correct if nec-
essary before cutting the workpiece.
4. Place workpiece on the saw table.
5. Start saw.
6. Cut workpiece in a single pass.
7. Switch off if no further cutting is to
be done immediately afterwards.
A
Danger!
Prior to all servicing:
switch machine OFF.
wait until the saw has come to a
complete stop.
unplug power cable.
Check that all safety devices are
operational again after each service.
Replace defective parts, especially
of safety devices, only with genuine
replacement parts. Parts not tested
and approved by the equipment
manufacturer can cause unforeseen
damage.
Repair and maintenance work other
than described in this section should
only be carried out by qualified spe-
cialists.
9.1 Adjusting the speed
By shifting the V-belts four different
speeds can be set.
The following materials can be cut when
using appropriate saw blades:
Shifting the V-belts
1. Open housing door.
2. Turn V-belt tensioning crank (56)
clockwise to slacken V-belt tension.
3. Reposition V-belts according to the
schema on the inside of the housing
door:
from motor pulley (58) to interme-
diate wheel(57);
from intermediate wheel (57) to
lower band saw wheel (55).
4. Turn V-belt tensioning crank (56)
counter-clockwise to tension V-
belts.
5. Close housing door.
6. Let saw test-run for at least one
minute.
7. Stop saw, unplug and check set-
tings.
9.2 Changing the band saw
blade
A
Danger!
Risk of injury, even with the
band saw blade at standstill. Wear
gloves when changing blades.
Use only suitable band saw blades
(see “Technical Specifications”).
1. Loosen screws (59) of locking bar
and open locking bar (60).
2. Open housing door.
3. Adjust upper blade guide (61) to its
lowest position.
4. Open lower blade guard (62).
5. Loosen setting knob (64) until the
band saw blade has slackened.
6. To remove the band saw blade,
guide it through
the slot in the saw table,
the blade guard on the upper
blade guide (63),
the lower blade guard (62) and
the blade guides.
7. Fit fresh band saw blade. Observe
correct position: the teeth point
towards the front (door) side of the
saw.
9. Care and Maintenance
3 mm
53 54
Cutting speed
[m/min]
Steel 68
Non-ferrous
metals, plastics
176
Hardwood 375
Wood 967
56
5758
55
59
60
61
62
63
64
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo BAS 505G bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo BAS 505G in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 8,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info