658553
16
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
ENGLISHen
16
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately
and handed in for environmentally compatible
recycling in accordance with European Directive
2002/96/EC on waste electrical and electronic
equipment and its implementation in national
legal systems.
Following you will find a description of problems
and faults that you may remedy yourself. If the
corrective measures described here do not help,
kindly refer to chapter 12. "Repairs".
Danger!
There are particularly many accidents in
connection with problems and faults. Therefore
keep in mind:
Disconnect the mains plug prior to any fault
service.
Check to see that all safety devices are
operational after each fault service.
Motor does not run
Undervoltage relay tripped by power failure:
switch on again.
No mains voltage
Check cables, plug, outlet and mains fuse.
Motor overheated, e.g. by a blunt band saw blade
or chip build-up in the housing:
remove cause for overheating, let cool down
for a few minutes, then start again.
Motor and band saw blade turn in the wrong
direction
Connection sequence of the phases is reversed
(only possible with saw with 400 V connection):
Have connection checked by a qualified
electrician.
Band saw blade wanders off the line of cut or
runs off the band saw wheels
Band saw blade is not running dead centre on the
band saw wheels:
correct tracking (see "Care and
Maintenance").
Band saw blade breaks
Incorrect tension:
correct band saw blade tension (see "Initial
Operation").
Load too high:
reduce pressure against band saw blade
(reduced feed rate).
Incorrect band saw blade:
replace band saw blade (see "Care and
Maintenance"):
thin work piece = narrow band saw blade,
thick work piece = wide band saw blade.
Band saw blade warped
Load too high:
avoid lateral pressure on the band saw blade.
Saw vibrates
Insufficient mounting:
Fasten saw properly to a suitable surface (see
"Initial operation").
Saw table loose:
align and fasten saw table.
Motor mount loose:
check fastening screws, tighten if necessary.
Dust extraction port blocked
No dust collector connected or suction capacity
insufficient:
Connection extraction unit or increase
extraction power (air speed >= 20 m/sec at the
chip extraction nozzles).
Band saw blade is still while the motor turns
Belt tension too low:
Increase belt tension using the setting knob
(40).
Explanations of the details on page xy.
Changes due to technological progress reserved.
U=Mains voltage
I=Rated power
F =Min. fuse protection
P
1
=Rated input power
P
2
=Power output
n
0
=No-load speed
v
0
=Cutting speed
S
L
=Band saw blade length
S
B
=Band saw blade width
S
D
=Max. blade thickness
H =Max. cutting height
W=Saw table swivel range
A
1
=Machine dimensions (LxWxH)
A
2
=Saw table dimensions (LxW)
A
h
=Working with frame
m=weight
D
1
=connection diameter of the extraction
nozzle
~ AC Power
Machine in protection class II
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be
higher or lower depending on the operating
conditions, the condition of the power tool or the
accessories. Please allow for breaks and periods
for assessment purposes when the load is lower.
Arrange protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value
(vector sum of three
directions) determined in accordance with EN
61029:
a
h
=vibration emission value
K
h
= Uncertainty (vibration)
Typical A-effective perceived sound levels
:
L
pA
=sound-pressure level
L
WA
=acoustic power level
K
pA
, K
WA
= uncertainty
Wear ear protectors!
13. Environmental Protection
14. Troubleshooting Guide
15. Technical Specifications
16

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Metabo-BAS-318-Precision

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo BAS 318 Precision bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo BAS 318 Precision in de taal/talen: Alle talen als bijlage per email.

De handleiding is 26,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info