494809
4
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
11
2. Hold down the selection key for the appliance to be
programmed for 5 seconds.
3. When the key is released, it will start to flash. Enter the
code 0000; the selection key flashes more quickly to
indicate that the remote control is ready for the search.
4. Point the remote control at the appliance. Press and slowly
release the ON/OFF key or PLAY for the VCR and DVD
several times, stopping when the appliance responds
correctly to the command.
5. When the appliance responds correctly, press OK to
confirm. Three flashes indicate that the search operation
has been completed correctly.
+++
0000
ADDITIONAL CHECK
Check that some of the other functions used on your original remote control are working correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar remote
control but not the right one. In this case, repeat the search procedure starting from point 2.
or
To display and make a note of the code memorized by means of the search,
follow the instructions described in the paragraph CURRENT CODE DISPLAY.
N.B. THE LIGHT INDICATOR STOPS FLASHING.
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• if a key other than ON/OFF or PLAY is accidentally pressed
• if the end of the code search list has been reached. In this case, start again from point 2 or
consult our website www.gumbodylight.com.
CURRENT CODE DISPLAY
In addition to what is described above, you can assign the selection keys to appliances other than those
indicated; for example, you can use the SAT key to control the TV. This allows every possible combination
according to your requirements; ust programme the remote control by means of procedure direct code
entry. To find out the appliance code if you have used procedure or , proceed as described in the
paragraph CURRENT CODE DISPLAY.
USING THE REMOTE CONTROL WITH MORE THAN ONE APPLIANCE OF THE SAME TYPE
B
A C
N.B. this operation cannot be interrupted and the remote control cannot
therefore be used until the end of the 4 series of flashes.
1. Hold down the selection key of the appliance whose code
you want to know for 5 seconds.
2. When the key is released it will start to flash; press and
release the 1-/-- key within 8 seconds.
3. After a few seconds, the light indicator produces 4 series
of flashes, with a pause between each series, correspon-
ding to the current code. Count the number of flashes;
each series of flashes corresponds to one figure in the
code. 10 flashes correspond to 0.
4. Make a note of the code on the adhesive label inside the
battery cover for quick and easy future reprogramming.
........................................................ = 1
............................................ = 3
= 0
.......................... = 6
Code obtained = 1306
To find out the code of your remote control, follow this procedure:
5 SEC.
or or or or or
5 SEC.
or or or or or
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Meliconi Gumbody universal 6 Light bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Meliconi Gumbody universal 6 Light in de taal/talen: Engels als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info