551340
16
Verklein
Vergroot
Pagina terug
1/21
Pagina verder
ENGLISH ENGLISH
10
11
InstallationInstallation
Step 3: Setup the Blaster and IR Sensor Step 4: Boot up the Transmitter and Receiver
If necessary, connect the Infrared (IR) blaster (or sensor) Extender cable. Users can point
hand-held remote control of your High Definition AV equipment at the receiver or the
HDTV set to operate the source devices, not exceeding the distance of 66 feet at Line-
of-sight.
IR Blaster Extender cable
Stick IR Blaster to the front
of panel of Source device
1. Plug the IR blaster cable into the IR OUT jack of the transmitter.
2. Please try to manually move the IR blaster in the front of the front panel of your HD de-
vice and then press the key of remote control to search a good position of IR response.
Paste the IR blaster head near the front of IR sensor of your High-Definition audio/video
devices.
3. When the IR blaster cable is connected, it relays infrared command from your remote
control to the device. Users can control their AV devices by pointing their remote con-
trol to the receiver instead of to their AV equipment.
1. Place the two AAA batteries into the remote control.
NOTE:
1. The IR sensor supports 36KHz ~ 56KHz (NEC, RC5, RC6) remote’s signal protocol. There-
fore, it is possible that some devices may not be supported.
2. The IR blaster supports 47KHz remote’ signal protocol.
NOTE:
User can press POWER button of transmitter to turn off both transmitter & receiver simul-
taneously any time.
2. After the power cord is plugged into the electrical outlet, the device will be turned on
automatically.
3. If it is in Standby mode (Both POWER LED of transmitter and receiver are lit in red),
press the POWER button on both transmitter and receiver to turn on the transmitter
and the receiver.
4. If transmitters HDMI out display is on (Transmitter POWER LED is lit in blue) and recei-
ver stay in Standby mode (Receiver POWER LED is lit in red), press the POWER button of
receiver ONLY to wake up and make connection between transmitter and the receiver
for enable display out on receiver side.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Megasat Wireless HD Sender Comfort bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Megasat Wireless HD Sender Comfort in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info