551366
1
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Model NO.: MV-9011C (with MP-001)
OMNI-DIRECTIONAL MARINE & CARAVAN TV ANTENNA
HDTV
Compatible
ATSC
Com pati ble
1
Frequency range:VHF:47-230MHz
UHF:470-862MHz
Receiving range: FM/VHF/UHF
Gain: 30dB
Noise figure: 3dB
Max. output level: 110dBµV
Impedance: 7
Connector: F-connectors
Power supply: DC 12V
1.Antenna x 1
2.Rubber ring x 1
3.Aluminum Mountx 1
4.Water-proof washer x 1
5.Roof Gasket x 1
6.Screw sets x 4
Hexagon Nuts x 4
Spring washer x 4
Antenna Gasket x 4
7.Carriage Bolts x 4
8.Power supply MP-001 kits
Technical Specification
Included in Packaging:
Installation Guide:
STEP 1. Choose Location
Antenna & power supply location determines wher
e and how you run cables, so please install under the following instructions:
Choose a location outside the roof which allow easy connection to power supply and television. Make sure the location is flat and
have sufficient space. See Figure1.
12V AC/DC power adapter
Gain adjuster
Power supply with gain adjuster
DC 12V input wire kits
8
2
{
6
{
6
4
5
3
7
water-proof washer
roof
roof gasket
Figure 1
Outside view of roof Inside view of roof
Specially compatible with HDTV of various digital terrestrial signal
(DVB-T,ISDB-T,DMB-T/H,ATSC) and DAB/FM radios.
The antenna is surface-treated to withstand impacts from saltwater
and weather conditions
Build-in high gain and low noise amplifier, shielded for minimum
interference.
Waterproof housing design made of UV resistant, injection molded
ASA material with super durability.
Omnidirectional antennas receive VHF, UHF, and FM signal from every
point regardless of the direction you are travelling.
The best digital terrestrial TV reception solution for your boating and caravans
SMD Technology and micro-electronics makes the high quality amplifier, ensure the
excellent antenna performance.
Product features
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Con nect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Con nect the antenna cable
Connect the antenna coaxial cable(Fem ale F connector ) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Con nect the antenna cable
Connect the antenna coaxial cable(Fem ale F connector ) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
Model NO.: MV-9011C (with MP-001)
OMNI-DIRECTIONAL MARINE & CARAVAN TV ANTENNA
HDTV
Compatible
ATSC
Com pati ble
1
Frequency range:VHF:47-230MHz
UHF:470-862MHz
Receiving range: FM/VHF/UHF
Gain: 30dB
Noise figure: 3dB
Max. output level: 110dBµV
Impedance: 7
Connector: F-connectors
Power supply: DC 12V
1.Antenna x 1
2.Rubber ring x 1
3.Aluminum Mountx 1
4.Water-proof washer x 1
5.Roof Gasket x 1
6.Screw sets x 4
Hexagon Nuts x 4
Spring washer x 4
Antenna Gasket x 4
7.Carriage Bolts x 4
8.Power supply MP-001 kits
Technical Specification
Included in Packaging:
Installation Guide:
STEP 1. Choose Location
Antenna & power supply location determines wher
e and how you run cables, so please install under the following instructions:
Choose a location outside the roof which allow easy connection to power supply and television. Make sure the location is flat and
have sufficient space. See Figure1.
12V AC/DC power adapter
Gain adjuster
Power supply with gain adjuster
DC 12V input wire kits
8
2
{
6
{
6
4
5
3
7
water-proof washer
roof
roof gasket
Figure 1
Outside view of roof Inside view of roof
Specially compatible with HDTV of various digital terrestrial signal
(DVB-T,ISDB-T,DMB-T/H,ATSC) and DAB/FM radios.
The antenna is surface-treated to withstand impacts from saltwater
and weather conditions
Build-in high gain and low noise amplifier, shielded for minimum
interference.
Waterproof housing design made of UV resistant, injection molded
ASA material with super durability.
Omnidirectional antennas receive VHF, UHF, and FM signal from every
point regardless of the direction you are travelling.
The best digital terrestrial TV reception solution for your boating and caravans
SMD Technology and micro-electronics makes the high quality amplifier, ensure the
excellent antenna performance.
Product features
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Con nect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Con nect the antenna cable
Connect the antenna coaxial cable(Fem ale F connector ) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Con nect the antenna cable
Connect the antenna coaxial cable(Fem ale F connector ) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Megasat T3 - DVB-T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Megasat T3 - DVB-T in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 4,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info