790487
15
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
7
3 Operating GB
Overview of all buttons on the remote control (advanced functions):
t Button for manual selection of the massage method:
Switch through in the following order: Kneading, tapping, swedish,
shiatsu, clapping, roll massage, end function.
r + f + g (only with manually selected massage activated):
r Change the direction/rhythm of the massage
g Change the speed of the back massage in ve steps
f For tapping, clapping, shiatsu, roll massage: Change the distance bet-
ween the massage heads in 3 steps.
uspot massage/partial back massage:
Spot massage at the current point on the back.
Press the button again to switch to partial back massage.
z/d Up/Down: Adjust massage position individually
s Heating function
1. button press = activation at knee/leg
2. button press = activation at knee/leg + massage heads
3. button press = switch off the heating function
i Air pressure massage of the whole body (automatic mode): on/off
oManual selection of air pressure massage areas:
Leg support -> Arm support -> Shoulders -> Off
p Adjust the intensity of the air pressure massage in 5 steps
(works in automatic and manual mode)
a Switch foot massage roller on and off
3.4 Switching off the device
Press the Power button 9 on the remote control.
All functions are terminated - but the massage heads are still moving to
their parking position. Wait a few seconds.
Then set the on/off switch (position 7) to position „O“ and disconnect the
device from the power socket.
3.5 Troubleshooting
problem possible cause suggestion
The device does not
work
The device is not plug-
ged in properly
Ensure the voltage
on the device corre-
sponds to the local
mains voltage and
then plug in again.
Make sure the outlet is
properly working.
The device stopped
working
The device has just
nished its auto timer
session and has auto-
matically switched to
standby mode.
If you want another
session, press the
power button again.
The device stopped
working
You may have used
the device continuous-
ly for 45 minutes
where the over-heat
protection has been
activated.
Unplug the device and
let it cool down for 60
minutes before you
use it again.
The device stopped
working
An excessive load has
been applied on the
device.
Reduce the excessive
load and start again.
The device is abnor-
mally warm
The device is likely to
be overused.
Unplug the device and
let it cool down before
using it again.
Noise can be heard
from the device
Noise is made by the
mechanical parts of
the device.
This is normal and
does not mean that
the device is faulty.
If the problem encountered is not listed, please try the following suggestions:
1. Turn off the product and unplug it.
2. Wait for 60 minutes.
3. Plug the product back to the recommended outlet and restart.
4. If the problem persists, contact the authorized service center.
The service centre address is shown on the attached leaet.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Medisana MS 2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Medisana MS 2000 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds, Fins als bijlage per email.

De handleiding is 4.47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info