481355
1
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
1
Preparation before use
Note:
If the air conditioner you purchased is a Cooling Only one, but you preset the remote controller as Heat Pump, it doesn't
bring any matter. But if the air conditioner you purchased is a Heat Pump one, and you preset the remote controller as
Cooling Only, then you CAN NOT preset the Heating operation with the remote controller.
Remote Controller presetting
Before using the air conditioner, be sure to check and preset the following.
The appliance is preset as no auto restart function by manufacturer. If you want auto restart function,
let the appliance is energized, hold down the Emergency button (ON/OFF) on the indoor unit for over
5 seconds, auto restart function is set with buzz sound, air conditioner is on standby.
If auto restart has been set, hold down the Emergency button (ON/OFF) on the indoor unit for over 5
seconds, auto restart function is canceled with buzz sound, air conditioner is on standby.
Auto Restart Presetting
The remote controller is NOT presetting as Cooling Only Air Conditioner or Heat Pump by manufacturer.
User can preset the remote controller type depending on the air conditioner type you have purchased
as follows:
Each time after the remote controller replaces batteries or is energized, the Cooling indicator and
Heating indicator will flashes alternately on LCD of the remote controller.
Press any button when flashes, Heat Pump is set.
Press any button when flashes, Cooling Only is set.
If you don't press any button within 12 seconds, the remote controller is preset as Heat Pump automatically.
Safety precautions
Symbols in this Use and Care Manual are interpreted as shown below.
Be sure not to do.
The feature of the appliance,
instead of a fault.
Pay attention to such a situation.
Grounding is essential.
Be sure to follow this instruction.
Do not use the power supply circuit
breaker or pull off the plug to turn it off
during operation. This may cause a fire
due to spark, etc.
Keep the power supply circuit breaker
or plug from dirt. Connect the power
supply cord to it firmly and correctly,
lest an electric shock or a fire break out
due to insufficient contact.
Use correct power supply in
accordance with the rating plate
requirement. Otherwise, serious
faults or hazard may occur or a
fire maybe break out.
Do not knit, pull or press the power supply
cord, lest the power supply cord be broken.
An electric shock or fire is probably caused
by a broken power supply cord.
Never insert a stick or similar obstacle
to the unit. Since the fan rotates at high
speed, this may cause an injury.
Do not repair the appliance by yourself.
If this is done incorrectly, it may cause an
electric shock, etc.
Turn off the appliance by remote control
firstly before cutting off power supply if
malfunction occurs.
It is harmful to your health if the cool air
reaches you for a long time. It is advisable
to let the air flow be deflected to all the room.
Prevent the air flow from reaching the gas
burners and stove.
Do not touch the operation buttons
when your hands are wet.
Do not put any objects on the outdoor
unit.
It is the user's responsibility to make the
appliance be grounded according to
local codes or ordinances by a licenced
technician.
OFF
OFF
ON
ON
Warning: Incorrect handling could
cause a serious hazard, such as death,
serious injury, etc.
2
FAN
MODE
TIM
E
R
ON
CLO
C
K
LO
C
K
T
IME
R
OF
F
SLE
E
P
SWIN
G
SM
AR
T
S
UP
ER
ON
OFF
Used to control the unit
when the remote
controller is out of work.
Used to set or cancel
auto restart function.
(See page 1)
Used to control the unit
when the remote
controller is out of work.
Used to set or cancel
auto restart function.
(See page 1)
It lights up during the
set time.
It lights up during the
set time.
.
.
It lights up when
compressor is running.
It lights up when
compressor is running.
Receive signal from
the remote controller.
Receive signal from the
remote controller.
Receive signal from the
remote controller.
It is on during operation.
It flashes during
defrosting.
It is on during operation.
It flashes during
defrosting.
It is on during operation.
It flashes during
defrosting.
RUN
TIMERCOMP
Used to control the unit
when the remote
controller is out of work.
Used to set or cancel
auto restart function.
(See page 1)
Emergency button
Emergency button
Emergency button
Timer Indicator(Yellow)
Timer Indicator
Compressor indicator
Compressor indicator
Signal Receptor
Signal Receptor
Signal Receptor
Run Indicator (Green)
Run Indicator
Run Indicator
ON/OFF
The shape and position of the switches and indicators may vary from different models, but their function are similar.
Identification of parts
4
Operating and Display
"K" ,"B" and "L" series
"N" series
Other series
COMP
TIMER
RUN
ON/OFF
RUN
ON/OFF
Indoor temperature
Indoor temperature
SMART button is ineffective in SUPER mode.
Target temperature
Target temperature
21 or below
26
or below
22
22
26
26
Over 26
Over 26
21 -23
23
-26
Your feeling
What you can do in SMART mode
button
adjustment procedure
Operation mode
Operation mode
HEATING
FAN ONLY
DRY
DRY
Room temperature
decrease 1.5
after
operate for 3 minutes
Room temperature
decrease 1.5 after
operate for 3 minutes
COOLING
COOLING
Press the SMART button, the unit enters SMART mode(fuzzy logic operation) directly regardless of
the unit is on or off. In this mode, temperature and fan speed are automatically set based on the
actual room temperature.
Uncomfortable
because of
unsuitable air
flow volume.
Uncomfortable
because of
unsuitable flow
direction.
Indoor fan speed alternates among
High, Medium and Low each time this
button is pressed.
Press it once, the vertical adjustment
louver swings to change vertical airflow
direction. Press it again, swings stops.
For horizontal airflow direction, please
refer to the previous page for details.
Operation mode and temperature are determined by indoor temperature
Note: Temperature, airflow and direction are controlled automatically in 6th mode.
However, a decrease or rise of up to 2 can be set with the remote controller if you still
feel uncomfortable.
Operation instructions
9
SMART mode
Heat pump models
Cooling only models
FAN
SWING
CLOCK button
You can adjust the real time by pressing CLOCK button, then
using and buttons to get the correct time, press
CLOCK button again the real time is set.
FAN
MODE
TIMER ON
CLOCK
LOCK
TIMER OFF
SLEEP
SW
ING
SMART
SUPER
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Maxicool SKL-50HOA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Maxicool SKL-50HOA in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 1,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info