Handleiding Maxdata Platinum 100 I (pagina 23 van 25) (Engels)

464013

Verklein

Vergroot

Pagina terug

1/25

Pagina verder

User’s Manual

MAXDATA PLATINUM 100 I

2 3MAXDATA PLATINUM 100 I M8Contents

Contents

1 Setting up the System 5

Safety Information ...................................................................................................................................5

Server Position ...................................................................................................................................5

System Access Warnings ..................................................................................................................6

Powering up the System .........................................................................................................................7

2 Board Features 9

Connector and Header Locations ..........................................................................................................10

Configuration Jumpers ..........................................................................................................................11

Back Panel Connectors .........................................................................................................................12

Hardware Requirements .......................................................................................................................13

Processor .........................................................................................................................................13

Memory ............................................................................................................................................13

3 Hardware Installations and Upgrades 15

Before You Begin ..................................................................................................................................15

Tools and Supplies Needed ..............................................................................................................15

Installing and Removing Memory ..........................................................................................................15

Installing DIMMs ..............................................................................................................................15

Replacing the Backup Battery ...............................................................................................................17

4 Server Utilities 19

Using the BIOS Setup Utility .................................................................................................................19

Starting Setup ...................................................................................................................................19

If You Cannot Access Setup .............................................................................................................19

Setup Menus ....................................................................................................................................19

Clearing the CMOS ...............................................................................................................................21

Configuring the System for embedded Serial ATA RAID ......................................................................22

Configuring the BIOS .......................................................................................................................22

Creating Intel

Matrix Storage Technology RAID set .......................................................................22

Creating LSI Technology RAID set ...................................................................................................22

Loading the RAID Drivers .................................................................................................................23

5 Regulatory and Compliance Information 25

Product Regulatory Compliance ............................................................................................................25

Product Safety Compliance ..............................................................................................................25

Product RoHS Compliance ...............................................................................................................25

Product EMC Compliance ...............................................................................................................25

Product Regulatory Compliance Markings .......................................................................................25

Electromagnetic Compatibility Notices .................................................................................................25

Europe (CE Declaration of Conformity) ............................................................................................25

4 PBMAXDATA PLATINUM 100 I M8Contents

Figures

1. PLATINUM 100 I Controls .................................................................................................................7

2. Board Connector and Component Locations ..................................................................................10

3. Configuration Jumpers ....................................................................................................................11

4. Back panel Connectors....................................................................................................................12

5. Installing DIMMs .............................................................................................................................15

6. Removing the Battery .....................................................................................................................18

Tables

1. Feature Summary ..............................................................................................................................9

2. Board Connectors and Components ...............................................................................................10

3. Configuration Jumpers ....................................................................................................................11

4. Back panel Connectors....................................................................................................................12

5. NIC LEDs .........................................................................................................................................12

6. Keyboard Commands ......................................................................................................................20

7. Product Certification Markings ........................................................................................................25

PB 5MAXDATA PLATINUM 100 I M8Setting up the System

1 Setting up the System

Safety Information

Server Position

Please take note of the following criteria for creating a practical and safe workplace when setting up

your computer:

 CAUTION

The system can be used anywhere the temperature is suitable for people. However, rooms with

humidity over 70%, and dusty or dirty areas are not appropriate. In addition, do not expose the server

to any temperatures over +30°C or under +10°C.

 CAUTION

For proper cooling and airflow, operate the system only with the chassis covers installed.

 CAUTION

Make sure that the cables connecting the server to peripheral devices are not tight.

 CAUTION

Make sure that all power and connection cables are positioned so that they are not trip hazards.

 CAUTION

When you save data to your server‘s hard disks or to a floppy disk, they are stored as magnetic

information on the media. Make sure that they are not damaged by magnetic or electromagnetic

fields.

 CAUTION

Because the electronics in your computer can be damaged by jarring, no mechanical devices should

be placed on the same surface as the server. This is especially important for impact printers whose

vibrations could damage the hard disk.

 CAUTION

Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on

power, telephone, and communication cables. Turn off the server and disconnect the power cord,

telecommunications systems, networks, and modems attached to the server before opening it.

Otherwise, personal injury or equipment damage can result.

 CAUTION

Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other

parts. We recommend that you perform all procedures in chapter 3 only at an ESD workstation. If one

is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis

ground ‑ any unpainted metal surface ‑ on your server when handling parts.

 ATTENTION

In order to fully separate the server from current, the power cord must be removed from the wall

outlet.

 ATTENTION

To ensure stability, the floor stands must be turned outwards (pedestal version only).

6 7MAXDATA PLATINUM 100 I M8Setting up the System

System Access Warnings

 CAUTION

To avoid personal injury or property damage, the following safety instructions apply whenever accessing

the inside of the product:

• Turn off all peripheral devices connected to this product.

• Turn off the system by pressing the power button to off.

• Disconnect the AC power by unplugging all AC power cords from the system or wall outlet.

• Disconnect all cables and telecommunication lines that are connected to the system.

• Retain all screws or other fasteners when removing access cover(s). Upon completion of

accessing inside the product, refasten access cover with original screws or fasteners.

• Do not access the inside of the power supply. There are no serviceable parts in the power

supply. Return to manufacturer for servicing.

• Power down the server and disconnect all power cords before adding or replacing any non hot‑

plug component.

• When replacing a hot‑plug power supply, unplug the power cord to the power supply being

replaced before removing the power supply from the server.

 CAUTION

If the server has been running, any installed processor(s) and heat sink(s) may be hot. Unless you

are adding or removing a hot‑plug component, allow the system to cool before opening the covers.

To avoid the possibility of coming into contact with hot component(s) during a hotplug installation,

be careful when removing or installing the hot‑plug component(s).

 CAUTION

To avoid injury do not contact moving fan blades. If your system is supplied with a guard over the

fan, do not operate the system without the fan guard in place.

6 7MAXDATA PLATINUM 100 I M8Setting up the System

Powering up the System

At the front of the case, you can find the necessary controls like power button and the HDD LEDs.

Press the power button one time briefly in order to boot the server.

Figure 1. PLATINUM 100 I Controls

A. Front USB ports

B. Power switch

C. Power LED

D. Reset switch

E. HDD LED

PB 9MAXDATA PLATINUM 100 I M8Board Features

2 Board Features

This chapter briefly describes the main features of the mainboard.

Table 1 summarizes the major features of the board.

Table 1. Feature Summary

Feature Description

Chassis Dimensions 450 mm high

195 mm wide

501 mm deep

18.0 kg max. chassis weight

Processor • Supports Dual-Core Intel

Xeon

processor 3000 series and Quad-

Core Intel

Xeon

processor 3200 series

• Supports Intel

Extended Memory System 64 Technology (EM64T)

Memory Four DIMM sockets supporting stacked DDR2 667/800 MHz ECC or

non-ECC unbuffered memory (up to 8 GB of total system memory)

Chipset Intel

3200 Chipset, consisting of:

• Intel

3200/3210 Memory Controller Hub (MCH)

• Intel

I/O Controller Hub (ICH9R)

• Intel

6702 PXH-V PCI-X Hub

Peripheral Interfaces Super I/O: Winbond 8374LF2

External connections:

• Stacked PS2 ports for keyboard and mouse

• DB9 Serial A port

• Two RJ45 NIC connectors for 10/100/1000 Mbps connections

• Two USB 2.0 ports

Internal connections:

• One USB port header which supports two USB 2.0 ports

• One DH10 Serial B header

• Six SATA connectors (3 Gbit/s) with integrated RAID support

• ATX-compliant 24-pin control panel header

Video On-board iBMC Server Engine with integrated video adapter and

external 32MB video memory

LAN • Intel

10/100/1000 82566E Gigabit Ethernet Controller

• Intel

10/100/1000 82541PI Gigabit Ethernet Controller

Expansion Capabilities • Two full length 32 bit / 33 MHz, 5 V Universal PCI connectors

• One x16 PCI Express connector

• One x8 PCI Express connector

• One physical x8 PCI Express connector (operating at x4 lane speed)

Fans Support for two system fans and one processor fan

System Management Intel

System Management Software

10 11MAXDATA PLATINUM 100 I M8Board Features

Connector and Header Locations

Figure 2 shows the approximate location of the major components on board.

Figure 2. Board Connector and Component Locations

Table 2. Board Connectors and Components

Label Description Label Description

A. PCI (5V/32bit/33MHz) Slot 1 S. Floppy Connector

B. PCI (5V/32bit/33MHz) Slot 2 T. HSBP

C. PCI Express x8 U. SATA 0

D. PCI Express x8 V. SATA1

E. PCI Express x16 W. SATA 2

F. System Fan 1 Connector X. IPMB

G. Back Panel Connectors Y. Front Panel Header

H. Diagnostic LEDs Z. SATA 4

I. Processor Fan 1 Connector AA. SATA 5

J. 2x4 Aux Power Connector BB. SATA 3

K. Processor Socket CC. Internal USB

L. Channel 2 DIMM Sockets DD. External USB

M. Channel 1 DIMM Sockets EE. CMOS Clear Jumper

N. System Fan 4 Connector FF. Password Clear Jumper

O. System Fan 3 Connector GG. BIOS Recovery Jumper

P. Battery HH. Serial Port

Q. Main Power Connector II. Chassis Intrusion Header

R. System Fan 2 Connector

A B F G H

VW U RS NOQ P M L

EDC

X T

10 11MAXDATA PLATINUM 100 I M8Board Features

Conﬁguration Jumpers

Figure 3 shows the location of the configuration jumpers.

Figure 3. Configuration Jumpers

Table 3. Configuration Jumpers

Jumper Name Function

BIOS Recovery • Pins 1-2: Normal operation

• Jumper removed: Recover from a corrupted BIOS. Bootable media

with a valid BIOS ROM is required.

Password Clear • Pins 1-2: Normal operation, protected passwords

• Pins 2-3: Erase password: If these pins are jumpered for 5 to 10

seconds, the password will be cleared on the next server reset. These

pins should not be jumpered for normal operation.

NOTE

The server does not need to be reset with the jumper on these pins for

the password to be cleared. To reset the password using this jumper:

Power down the server. Place the jumper on pins 2-3 for 5 to 10

seconds. Move the jumper back to pins 1-2. Power on the server.

CMOS Clear • Pins 1-2: Normal operation

• Pins 2-3: Erase CMOS: If these pins are jumpered for 5 to 10 seconds,

the CMOS settings will be cleared on the next server reset. These pins

should not be jumpered for normal operation.

NOTE

The server does not need to be reset with the jumper on these pins for

the CMOS to be cleared. To clear the CMOS: Power down the server.

Place the jumper on pins 2-3 for 5 to 10 seconds. Move the jumper back

to pins 1-2. Power on the server.

J1E3

J1E1

J1E2

CMOS

Clear

Default

CLEAR

CMOS

BIOS

Recovery

Default

Remove jumper for

BIOS recovery

Password

Clear

12 13MAXDATA PLATINUM 100 I M8Board Features

Back Panel Connectors

Figure 4. Back panel Connectors

Table 4. Back panel Connectors

Label Description Label Description

A. Stacked PS2 Mouse/Keyboard Ports D. NIC 1/2 (10/100/1000 Mbps)

B. Serial A E. USB1-2

C. Video

The NIC LEDs at the right and left of the NIC provide the following information:

Table 5. NIC LEDs

LED LED State Description

Right Off No network connection

Solid Green Network connection in place

Blinking Green Transmit/receive activity

Left Off 10 Mbps connection (if left LED is on or blinking)

Solid Green 100 Mbps connection

Solid Amber 1000 Mbps connection

12 13MAXDATA PLATINUM 100 I M8Board Features

Hardware Requirements

To avoid integration difficulties and possible board damage, your system must meet the requirements

outlined below.

Processor

Supports Dual‑Core Intel

Xeon

processor 3000 series and Quad‑Core Intel

Xeon

processor 3200

series.

Memory

The Server Board provides four DIMM sockets across two banks. Bank 1 consists of DIMM sockets

A1 and B1. Bank 2 consists of DIMM sockets A2 and B2. Minimum memory operation is a single

512MB DIMM in socket A1. This will provide single‑channel interleave. For dual‑channel interleave,

two identical DIMMs are required in sockets A1 and B1.

To operate in dual‑channel dynamic paging mode, the following conditions must be met:

• Populate two identical DIMMs in sockets DIMM A1 and DIMM B1.

• Populate four identical DIMMs in each socket location.

/ Note

The use of three DIMMs is not supported. Use DIMMs that are the same type and speed. Use of

identical DIMMs is preferred.

DIMMs must meet the following requirements:

• Use only DIMMs with DDR2 DRAM technology.

• Use only DDR2‑667 and DDR2‑800 stacked DIMM modules.

PB 15MAXDATA PLATINUM 100 I M8Hardware Installations and Upgrades

3 Hardware Installations and Upgrades

Before You Begin

Before working with your server product, pay close attention to the “Safety Information” at the

beginning of this manual.

Tools and Supplies Needed

• Phillips (cross head) screwdriver (#1 bit and #2 bit)

• Needle nosed pliers

• Antistatic wrist strap and conductive foam pad (recommended)

Installing and Removing Memory

The silkscreen on the board for the DIMMs displays DIMM A1, DIMM A2, DIMM B1, DIMM B2

starting from the center of the board. DIMM A1 is the socket closest to the processor socket. See

„Memory“ for a discussion of the memory requirements and options.

Installing DIMMs

To install DIMMs, follow these steps:

1. Observe the safety and ESD precautions in “Safety Information”.

2. Turn off all peripheral devices connected to the server. Turn off the server.

3. Disconnect the AC power cord from the server.

4. Remove the server‘s cover.

5. Locate the DIMM sockets (see Figure 5).

Figure 5. Installing DIMMs

DIMM A1

DIMM A2

DIMM B2

DIMM B1

16 17MAXDATA PLATINUM 100 I M8Hardware Installations and Upgrades

6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open

position (see letter “A” in Figure 5).

7. Holding the DIMM by the edges, remove it from its anti‑static package.

8. Position the DIMM above the socket. Align the notch on the bottom edge of the DIMM with

the key in the DIMM socket (see letter “B” in Figure 5).

9. Insert the bottom edge of the DIMM into the socket (see letter “C” in Figure 5).

10. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips

snap into place. Make sure the clips are firmly in place (see letter “D” in Figure 5).

11. Replace the server‘s cover and reconnect the AC power cord.

16 17MAXDATA PLATINUM 100 I M8Hardware Installations and Upgrades

Replacing the Backup Battery

The lithium battery on the server board powers the RTC for up to 10 years in the absence of power.

When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in

the RTC (for example, the date and time) may be wrong. Contact your customer service representative

or dealer for a list of approved devices.

 WARNING

Dangerofexplosionifbatteryisincorrectlyreplaced.Replaceonlywiththesameorequivalent

type recommended by the equipmentmanufacturer. Discardused batteries accordingto

manufacturer’sinstructions.

 WARNUNG

Wenn eine ungeeignete Batterie eingesetztwird oder dieBatterie falsch eingesetzt wird,

bestehtExplosionsgefahr.ErsetzenSieverbrauchteBatteriennurdurchBatteriengleichen

oderäquivalentenTyps,dervomHerstellerempfohlenwurde.EntsorgenSiedieverbrauchte

BatterieentsprechenddenAnweisungendesHerstellers.

 AVERTISSEMENT

Dangerd’explosionencasderemplacementincorrectdelapile.Remplacez-launiquement

parunepiledumêmetypeoud’untypeéquivalentrecommandéparlefabricant.Mettezau

rebutlespilesusagéesenvousconformantauxinstructionsdufabricant.

 OSTRZEŻENIE

Nieprawidłowa wymiana baterii grozi eksplozją. Wymieniać tylko na taki sam lub

równoważnytyp,zalecanyprzezproducenta.Zużytebaterieutylizowaćzgodniezinstrukcjami

producenta.

 ADVARSEL

Lithiumbatteri-Eksplosionsfarevedfejlagtighåndtering.Udskiftningmåkunskemedbatteri

afsammefabrikatogtype.Levérdetbrugtebatteritilbagetilleverandøren.

 ADVARSEL

Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av

apparatfabrikanten.Bruktbatterireturneresapparatleverandøren.

 VARNING

Explosionsfaravid felaktigtbatteribyte.Använd sammabatterityp eller en ekvivalenttyp

som rekommenderas av apparattillverkaren.Kassera använt batteri enligt fabrikantens

instruktion.

 VAROITUS

Paristovoiräjähtää,josseonvirheellisestiasennettu.Vaihdaparistoainoastaanlaitevalmistajan

suosittelemaantyyppiin.Hävitäkäytettyparistovalmistajanohjeidenmukaisesti.

18 PBMAXDATA PLATINUM 100 I M8Hardware Installations and Upgrades

To replace the battery, follow these steps:

1. Observe the safety and ESD precautions in “Safety Information”.

2. Turn off all peripheral devices connected to the server. Turn off the server.

3. Disconnect the AC power cord from the server.

4. Remove the server‘s cover and locate the battery.

5. Lift the battery retention mechanism (see Figure 6).

6. Remove the battery from its socket.

Figure 6. Removing the Battery

7. Dispose of the battery according to local ordinance.

8. Remove the new lithium battery from its package, and, being careful to observe the correct

polarity, insert it in the battery socket.

9. Close the chassis.

10. Run Setup to restore the configuration settings to the RTC.

PB 19MAXDATA PLATINUM 100 I M8Server Utilities

4 Server Utilities

Using the BIOS Setup Utility

This section describes the BIOS Setup Utility options, which is used to change server configuration

defaults. You can run BIOS Setup with or without an operating system being present.

Starting Setup

You can enter and start BIOS Setup under several conditions:

• When you turn on the server, after POST completes the memory test

• When you have moved the CMOS jumper on the server board to the “Clear CMOS” position

(enabled)

In the two conditions listed above, during the Power On Self Test (POST), you will see this prompt:

Press <F2> to enter SETUP

In a third condition, when CMOS/NVRAM has been corrupted, you will see other prompts but not

the <F2> prompt:

Warning: CMOS checksum invalid

Warning: CMOS time and date not set

In this condition, the BIOS will load default values for CMOS and attempt to boot.

If You Cannot Access Setup

If you are not able to access BIOS Setup, you might need to clear the CMOS memory. For instructions

on clearing the CMOS, see “Clearing the CMOS”.

Setup Menus

Each BIOS Setup menu page contains a number of features. Except for those features that are

provided only to display automatically configured information, each feature is associated with a

value field that contains user‑selectable parameters. These parameters can be changed if the user

has adequate security rights. If a value cannot be changed for any reason, the feature’s value field

is inaccessible.

20 21MAXDATA PLATINUM 100 I M8Server Utilities

Table 6 describes the keyboard commands you can use in the BIOS Setup menus.

Table 6. Keyboard Commands

Press Description

<F1> Help - Pressing F1 on any menu invokes the general Help window.

← →

The left and right arrow keys are used to move between the major menu pages.

The keys have no affect if a sub menu or pick list is displayed.

↑

Select Item up - The up arrow is used to select the previous value in a menu

item’s option list, or a value field pick list. Pressing the Enter key activates the

selected item.

↓

Select Item down - The down arrow is used to select the next value in a menu

item’s option list, or a value field pick list. Pressing the Enter key activates the

selected item.

F5/‑ Change Value - The minus key or the F5 function key is used to change the value

of the current item to the previous value. This key scrolls through the values in

the associated pick list without displaying the full list.

F6/+ Change Value - The plus key or the F6 function key is used to change the value

of the current menu item to the next value. This key scrolls through the values

in the associated pick list without displaying the full list. On 106-key Japanese

keyboards, the plus key has a different scan code than the plus key on the other

keyboard, but it has the same effect.

<Enter> Execute Command - The Enter key is used to activate submenus when the

selected feature is a sub menu, or to display a pick list if a selected feature has

a value field, or to select a sub-field for multi-valued features like time and date.

If a pick list is displayed, the Enter key will undo the pick list, and allow another

selection in the parent menu.

<Esc> Exit - The ESC key provides a mechanism for backing out of any field. This key

will undo the pressing of the Enter key. When the ESC key is pressed while

editing any field or selecting features of a menu, the parent menu is re-entered.

When the ESC key is pressed in any sub menu, the parent menu is re-entered.

When the ESC key is pressed in any major menu, the exit confirmation window

is displayed and the user is asked whether changes can be discarded.

<F9> Setup Defaults - Pressing F9 causes the following to appear:

Setup Confirmation

Load default configuration now?

[Yes] [No]

If “Yes” is selected and the Enter key is pressed, all Setup fields are set to their

default values. If “No” is selected and the Enter key is pressed, or if the ESC

key is pressed, the user is returned to where they were before F9 was pressed

without affecting any existing field values.

<F10> Save and Exit - Pressing F10 causes the following message to appear:

Setup Confirmation

Save Configuration changes and exit now?

[Yes] [No]

If “Yes” is selected and the Enter key is pressed, all changes are saved and

Setup is exited. If “No” is selected and the Enter key is pressed, or the ESC key

is pressed, the user is returned to where they were before F10 was pressed

without affecting any existing values.

20 21MAXDATA PLATINUM 100 I M8Server Utilities

Clearing the CMOS

If you are not able to access the BIOS setup screens, the CMOS Clear jumper will need to be used

to reset the configuration RAM.

1. Power down the system and disconnect the AC power.

2. Open the server.

3. Move the jumper from the normal operation position, at pins 1 and 2, to the CMOS Clear

position, covering pins 2 and 3.

4. Wait 5 to 10 seconds.

5. Return the CMOS Clear jumper to the Normal location, covering pins 1 and 2.

6. Close the server chassis.

7. Reconnect the AC power and power up the system.

22 23MAXDATA PLATINUM 100 I M8Server Utilities

Conﬁguring the System for embedded Serial ATA RAID

Conﬁguring the BIOS

1. Make sure you are having at least two SATA hard drives.

2. Enter system BIOS Setup by pressing the <F2> key after the Power‑On‑Self‑Test (POST)

memory tests begin.

3. Go to “Advanced” ‑ “SATA Controller Configuration”; ensure “Configure SATA as” is set

to “RAID”. Post product launch an additional selection between LSI and Intel

RAID will be

possible here. At launch the Intel

Matrix Storage Manager Option will be enabled by this

setting.

4. Save your settings by pressing <F10>.

Creating Intel

Matrix Storage Technology RAID set

/ NOTE

This RAID is supported for Windows operating systems only.

1. Upon re‑boot you will see the Intel

Matrix Storage Manager Option ROM status message on

the screen. Press CTRL‑I to enter the RAID Option ROM user interface.

2. In the User Interface menu, select option #1; Create RAID Volume. Enter a volume name,press

<enter>. The RAID Volume name must be in English alphanumeric ASCII characters.

3. Use the arrow keys to select the RAID level (0/1/5/10), press <enter>.

4. Select the drives to be used in the RAID array (only if there are more than two drives available),

press <enter>.

5. Select the stripe size (only for RAID 0/5), and press <enter>.

6. Enter the size of the volume (If you select less than the maximum volume size you can create

a second RAID array on the remaining portion of your volume, not recommended), and press

<enter>.

7. Finally press <Y> to confirm your selections.

8. Exit the Option ROM user interface by pressing <ESC>.

Creating LSI Technology RAID set

/ NOTE

This option will be implemented post product launch.

1. Upon re‑boot you will see the Embedded RAID Option ROM status message on the screen.

Press CTRL‑E to enter the RAID Option ROM user interface.

2. In the Management Menu, select option #1: “Configure”. Choose “Easy Configuration”.

3. Mark ready drives to be used in the RAID array using the space bar and press F10 to end

selection.

4. On the “Select Configurable Arrays” screen press <space> and <F10>.

5. Enter the properties of the new RAID: RAID Level (0/1/10), Size, Stripe Size. Accept the

settings.

6. Exit the Easy Configuration Screen using <ESC> and save the configuration.

7. Return to the Management Menu and Initialize the new RAID.

8. Exit the Option ROM user interface by pressing <ESC>.

22 23MAXDATA PLATINUM 100 I M8Server Utilities

Loading the RAID Drivers

1. Begin Microsoft

Windows

Setup by booting from the Microsoft

Windows

installation CD.

2. At the beginning of Microsoft

Windows

Setup, press <F6> to install a third‑party SCSI or

RAID driver. When prompted, insert the floppy with the RAID driver. Install the appropiate

SATA RAID Controller driver, either “Intel(R) ICH9R SATA RAID Controller” for Intel

Matrix

Storage Technology RAID set or “Intel Embedded Server RAID Technology” for LSI technology

RAID set.

3. Finish the Microsoft

Windows

installation and install all necessary drivers.

4. Install the monitoring software included with your motherboard or after downloading it from

the Internet: LSI MegaIDESpy or Intel

Matrix Storage Manager depending on the RAID

technology you chose previously. This will allow for local monitoring of the RAID configuration.

Additionally errors will be entered to the local system log files.

24 PBMAXDATA PLATINUM 200 I M8

PB 25MAXDATA PLATINUM 100 I M8Regulatory and Compliance Information

5 Regulatory and Compliance Information

Product Regulatory Compliance

Product Safety Compliance

The server complies with the following safety requirements:

• EN 60950 (European Union)

• CE – Low Voltage Directive (73/23/EEC) (European Union)

Product RoHS Compliance

Restriction of Hazardous Substances: This server system is compliant to European Directive 2002/95/

EC (RoHS).

Product EMC Compliance

The server has been tested and verified to comply with the following electromagnetic compatibility

(EMC) regulations:

• EN 55022 (Class A) – Radiated & Conducted Emissions (European Union)

• EN 55024 (Immunity) (European Union)

• CE – EMC Directive (89/336/EEC) (European Union)

Product Regulatory Compliance Markings

This product is marked with the following Product Certification Markings:

Table 7. Product Certification Markings

CE Mark

Electromagnetic Compatibility Notices

Europe (CE Declaration of Conformity)

This product has been tested in accordance too, and complies with the Low Voltage Directive (73/23/

EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate

its compliance.

Maxdata Platinum 100 I Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Maxdata Platinum 100 I

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info