Handleiding Matrix MEH601 (pagina 10 van 16) (Engels)

738382

Verklein

Vergroot

Pagina terug

1/16

Pagina verder

Chimney Extractors

Manual for installation,

use and maintenance

MEH & MEP

parts + 1 year labour

year

guarantee

www.matrixappliances.co.uk

Important

The CDA Group Ltd cannot be held responsible for injuries or losses

caused by incorrect use or installation of this product. Please note

that CDA reserve the right to invalidate the guarantee supplied with

this product following incorrect installation or misuse of the appliance

or use in a commercial environment.

This appliance is not designed to be used by people (including

children) with reduced physical, sensorial or mental capacity, or

who lack experience or knowledge about it, unless they have had

supervision or instructions on how to use the appliance by someone

who is responsible for their safety.

Under no circumstances should any external covers be removed for

servicing or maintenance except by suitably qualified personnel.

Appliance information:

Please enter the details on the appliance rating plate below for

reference, to assist CDA Customer Care in the event of a fault

with your appliance and to register your appliance for guarantee

purposes.

Appliance Model

Serial Number

EU Declarations of Conformity

This appliance has been manufactured to the strictest standards

and complies with all applicable legislation, including Electrical safety

(LVD) 2014/35/EU and Electromagnetic interference (EMC) 2014/30/

EU.

Parts intended to come into contact with food conform to 1935/2004/

EC.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE

PRODUCT IN ACCORDANCE WITH EU DIRECTIVE 2012/19/EU.

At the end of its working life, the product must be taken to a special

local authority waste collection centre or to a dealer providing

appliance recycling services.

Disposing of a household appliance separately avoids possible

negative consequences for the environment and health. It also

enables the constituent materials to be recovered, saving both

energy and resources. As a reminder of the need to dispose of

household appliances separately, the product is marked with a

crossed-out wheeled dustbin.

Please note:

• Under no circumstances should the extractor be connected to any

gas ventilation system, flue system or hot air ducting system.

• Do not vent the extractor into an attic or loft space.

• Only house the extractor in rooms with adequate ventilation.

Remember that the extractor is powerful and whatever air is

extracted needs to be replaced.

• Do not tile the extractor in. It should be removable for service or

maintenance.

• Do not use silicone sealant to secure the hood to the wall.

• You must be able to isolate the extractor from the mains electrical

supply after installation.

• Steam cleaners must not be used when cleaning this appliance.

• The performance of your extractor will vary depending on a

number of factors. These include: type of extraction, length of

ducting, room volume, ventilation available and cleanliness of the

filters.

Using your extractor

For best performance, you should switch on the extractor 15 minutes

before starting to cook and leave it to run for approximately 15 minutes

after the end of cooking.

Control Panel

A = Power off button B = Speed level buttons C = Light button

To switch the extractor light on or off

• Press button C.

To switch on the extractor or change the motor speed at any time

when the extractor is running

• Press the relevant speed button (B) for the first, second or third speed

as required.

To switch the extractor off

• Press button A.

Fig. 1

A B C

Care and Maintenance

IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF

THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY

SUPPLY.

Cleaning

You should use a nonabrasive cleaner. Any abrasive cleaner

(including Cif) will scratch the surface and could erase the control

panel markings.

You can clean your extractor effectively by simply using a dilute solution

of water and mild detergent and drying to a shine with a clean cloth.

Cleaning the grease filter

The grease filter should be kept clean to minimise the risk of fire.

At least once a month you should remove and clean the grease

filter with hot soapy water. You can also wash the grease filter in a

dishwasher, ensuring that you place it in an upright position to prevent

damage from other items in the dishwasher. After rinsing and drying,

replace the filter.

To remove the grease filter, push in

the button on the handle and then

pull down on the filter at the front.

When you have released it at the

front, then you can pull out the filter.

To replace the grease filter, repeat

the steps in reverse.

Fig. 2

Please note:

Cleaning the grease filter in the dishwasher may lead to discolouration.

This is normal and does not constitute a fault with the appliance.

Changing the charcoal filter (re-circulating only)

To ensure best performance of your extractor, you should replace the

charcoal filter every four to six months, depending on use.

To attach a new charcoal filter, first remove the grease filters as

described above.

Insert the charcoal filter into the guide on the side of the motor, then

slide the filter in until it locks into place. Repeat with the second filter on

the opposite side. Finally replace the grease filters.

Changing the light bulbs

DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE

BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT.

Unscrew the light bulb cover. Unscrew the light bulb and replace with

the required 40W max candle bulb E14 SES. Finally, replace the light

bulb cover.

Do not touch bulbs or adjacent areas during or straight after prolonged

use of the lights.

The light is designed for use during cooking and not for general room

illumination. Extended use of the light can reduce the life span of the

bulb.

Bulb replacement is not covered by the guarantee.

Only use bulbs recommended for your extractor. Do not fit bulbs of a

higher power rating.

Bulbs of a lower power rating may be adequate for use, generally last

longer and use less energy.

Electrical Information

Mains electrical voltage: 230 – 240Vac, 50Hz

Total rated power consumption:

128W

Troubleshooting

If your extractor is not working:

1. Check that the mains supply has not been switched off.

2. Check that the fuse in the spur has not blown.

Mains Electricity Connection

THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY

A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE

SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE.

Warning! This appliance must be earthed

We recommend that the appliance is connected by a qualified

electrician, who is a member of the N.I.C.E.I.C. and who will comply

with the I.E.T. and local regulations.

The wires in the mains lead of this appliance are coloured in

accordance with the following code:

Green & Yellow = Earth, Blue = Neutral, Brown = Live.

As the colours of the wires in the mains lead for the appliance may

not correspond

to the coloured markings identifying the terminals connecting to the

fuse spur,

proceed as follows:

• The wire which is coloured green and yellow must be connected to

the

terminal marked E (Earth) or coloured green.

• The wire which is coloured blue must be connected to the terminal

marked

N (Neutral) or coloured black.

• The wire which is coloured brown must be connected to the terminal

marked

L (Live), or coloured red.

Note: Use a 3A Fuse

Assembly and electrical connection should be carried out by

specialised personnel.

When installing this product we recommend you seek the help of

another individual.

Do not mount the isolation switch behind the chimney section. It is a

requirement that you must be able to isolate the extractor from the

mains electrical supply after installation.

This appliance is intended to be connected to the mains electrical

supply by means of an isolation switch and fused spur and is

intended to be protected by a 3A fuse. The use of a 13A fuse can

cause damage to the internal wiring in the event of a fault, and may

also invalidate the warranty.

DOUBLE POLE SWITCHED

FUSE SPUR OUTLET

USE A 3 AMP FUSE

Fig. 3

Mounting your extractor

When the extractor is to be installed

above an electric hob, the minimum

distance between the hob and

extractor must exceed 600mm (650mm

is recommended).

When the extractor is to be installed

above a gas hob, the minimum

distance between the hob and

extractor must exceed 700mm (750mm

is recommended).

* The actual height of C depends

on the height of the ceiling and the

position of the hob.

If the instructions provided with your gas

hob state that the required distance

between the hob and extractor must

be greater than 700mm, then that is the

distance that should be observed; this

is a legal requirement and may lead to

your hob being disconnected from the

gas supply and the installation being

reported under RIDDOR (The height

should be measured from the top of

the burners).

Fig. 4

Gas: 750mm recommended.

Electric: 650mm recommended.

MEH601 MEH901 MEP601/901

A 60.5 60.5 53.5

B 120.5 120.5 169.5

C* 725 max 725 max 550

D 175 200 105

E 75 75 75

F 80 80 73

Fig. 5

IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE GAS

HOB, THE MINIMUM DISTANCE BETWEEN THE HOB AND EXTRACTOR

MUST BE AT LEAST 760mm.

The width of any hob must not be greater than the width of the extractor

installed above it (Fig. 4).

Ducting and Ventilation

For best performance and lowest noise output, we recommend the

use of 125mm ducting. You can also use 100mm ducting but this will

reduce performance.

Wherever possible utilise rigid circular pipe which has a smooth

interior, rather than the expanding concertina type ducting. The

lengths of the ducting without performance being affected are as

follows:

• 4 metres with 1 x 90° bend.

• 3 metres with 2 x 90° bends.

• 2 metres with 3 x 90° bends.

Longer ducting can be used but the performance of the extractor will

likely be reduced.

Please note: Ducting components and ducting kits are optional

accessories and have to be ordered, they are not automatically

supplied with the hood. Use of ducting less than 125mm in diameter

will affect performance and increase the noise produced by the

extractor.

Installation steps

Fig. 6 Fig. 7

Figu re 2 - M ark wal l as required (see ta ble 1)

Fig. 9

Figu re 3 - Drill h oles

Fig. 10 Fig. 11

Figu re 5 - Secure hoo d (tigh ten all screws)

Figu re 6 - Fit ductin g adap tor

Tools required Mark wall as required (see table 2)

Fit wall fixings and top screws -

Ensure that any fixings you use are

appropriate for the wall type.

Secure hood (tighten all screws)

IMPORTANT SAFETY WARNING: ONLY USE THE SCREWS PROVIDED

WITH THE EXTRACTOR TO MOUNT THE DUCTING ADAPTOR. THE USE

OF LONGER SCREWS MAY CAUSE DAMAGE TO THE INTERNAL WIRING

WHICH WILL NOT BE COVERED BY THE WARRANTY.

Drill holesDrill holes

Fig. 8

Fit ducting adaptor

Fig. 13

Fig. 14

Fig. 15

Fix ducting (seal joint)

Mount the chimney Adjust and secure the

chimney

Fig. 12

The metal casing of this appliance has been coated with a

preservative to protect it during transport and storage. This should

be removed during installation by using a non-abrasive stainless

steel cleaner. Always follow the instructions given with the cleaner

being used.

Fix ducting (seal joint)

Mount the chimney Adjust and secure the chimney

Mount chimney brackets

st an

NOTES:

Attribute Symbol Units

noitacifitnedI ledoM

Annual Energy Consumption AEC

Hood

kWh

Time increase factor f 1.6 1.6 1.7

Fluid Dynamic Eciency FDE

Hood

Energy Eciency Index EEI

Hood

84.1

Measured airﬂow at Best Eciency

Point

BEP

Measured Pressure at Best Eciency

Point

BEP

172.0 200 184.0 Pa

Qwolfria mumixaM

MAX

382.3 372.1

Measured electric power at Best

Eciency Point

BEP

91.8 91.6

Nominal lighting power WL 8

Average illumination of the lighting

system on the cooking surface

Middle

Measured power consumption in

standby

NA NA NA W

Measured power consumption o

mode

0.0 0.0 0.0 W

Sound power level L

67.0 70.0 69.0 dBA

Grease Filter Eciency GFE

Hood

63.4 (E) 64.2 (E) 66.4 (D) %

ELycneiciffe pmaL

Hood

Energy Efficiency Information

Value

MEH601 MEH901 MEP601/901

59 58.8 64.2

11.5 11.6

181.8

9.6

83.9 88.1

190.3220.9

336.4

96.6 W

Lux114 114 114

14.3(D) 14.3(D) 14.3(D) %

For our Customer Care Department, or for Service,

please contact us on:

Serviced by

The CDA Group Ltd. Harby Road, Langar, Nottinghamshire, NG13 9HY

Tel: 01949 862012 Fax: 01949 862003 Email: customer.care@cda.eu

Matrix MEH601 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info