442799

Marshall JVM410 Series Handleiding

5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
76
ENGLISH
ENGLISH
Channel Section
Pressing a channel button has two functions:
When coming from a different channel it recalls
the last setting in the new selected channel.
When pressing in the same channel it cycles the
modes: GREEN > ORANGE > RED > GREEN...
Each mode remembers the FX, Reverb and
Master settings.
Example: You are in OD1 ORANGE with FX +
REVERB and you press CLEAN. The amp
switches to the last Clean mode you had (let's
assume it was CLEAN GREEN with REVERB).
If you press the OD1 switch you go back to OD1
ORANGE with FX + REVERB. This allows
bouncing between channels without losing the
settings. If you now press OD1 again, you go to
OD1 RED with whatever FX, MASTER and
REVERB settings you had last time you were in
this mode.
Pressing REVERB switches the reverb ON and
OFF in the current channel.
Pressing FX LOOP switches the parallel FX loop
ON and OFF in the current channel.
Master Section
5. REVERB Control
Alongside the REVERB switch each channel
has its own reverb control allowing individual
level settings of the effect.
6. MASTER 1 / MASTER 2
These are the master volume controls of the
amplifier. They can be assigned individually to
each of the modes as you wish and their setting
will be remembered in each of the modes.
7. PRESENCE, RESONANCE
These controls are power amplifier controls and
only have effect when playing through a speaker
(not in silent recording). They affect how the
power amplifier reacts to the connected
speakers and how much control the amplifier
has over them.
Increasing the RESONANCE control
emphasises the natural speakers resonance for
an improved bass response. In the same way,
increasing the PRESENCE control emphasises
the speaker’s high frequencies which will be
heard as an improved high frequency response
which adds presence to the sound.
Presence and Resonance constitute a powerful
power amplifier equaliser, allowing responses
from a ‘^’ shape when they are fully off, which is
felt as a mid boost, to a ‘v’ shape when they are
turned clockwise, which is felt as a scooped
sound. Again, the effectiveness of these controls
is highly dependant on the kind of connected
speakers. Care has to be taken to avoid over
excursion of the speaker cones in high
resonance settings.
8. FX LOOP
This is a programmable FX loop which features
a MIX control on the rear panel and it is located
after the pre-amp, right before the reverb and
serial loop circuits. Pressing the FX Switch
engages this effects loop. Please refer to the
Serial / Parallel Loop description later on in the
handbook for its operation.
9. FOOTSWITCH / MIDI PROGRAM
This switch has a dual function:
Pressing it once we enter the FOOTSWITCH
PROGRAM mode. It is indicated by a
continuous red light.
Pressing it twice we enter the MIDI PROGRAM
mode. It is indicated by a blinking red light.
Footswitch program and use
The JVM range features a new type of fully
configurable footswitch. Connection to the
amplifier requires a standard mono 1/4" jack to
jack cable. Any guitar lead will work and
practically there should be no limit in its length.
When the front panel FOOTSWITCH / MIDI
PROGRAM switch is off, the footswitch operates
in safe mode and executes the commands the
moment the switch is pressed down.
If you enter the FOOTSWTICH PROGRAM
mode (LED red) you will be able to program the
footswitch but nevertheless the footswitch and
the amplifier will remain fully operational with the
only difference that the commands will be
executed when releasing the footswitches, as
opposed to the normal mode.
Each of the individual footswitches has 2 modes
of operation: preset store and switch store.
In preset store mode, any of the footswitches
can be configured to store the current amplifier
status. The current channel, master, FX and
reverb status will be stored and recalled when
the respective footswitch is pressed.
To store the current status simply:
Set the amplifier to FOOTSWITCH PROGRAM
mode (red light ON).
Press and hold the desired switch for about 3
seconds.
The FX footswitch LED will flicker a couple of
times indicating that the preset has been stored.
In switch store mode, any of the footswitches
can be configured to replicate the front panel
switches and the amplifier will react exactly in
the same way as when you operate them on the
front panel.
All the front panel switches can be mapped to
any of the footswitches without any limitation.
The only exception is the FOOTSWITCH / MIDI
PROGRAM key which cannot be assigned to
the footswitch.
To assign any of the front panel keys (except
FOOTSWITCH / MIDI PROGRAM) to any of the
footswitches simply:
Set the amplifier to FOOTSWITCH PROGRAM
mode (red light ON).
Press and hold the desired footswitch.
While holding the footswitch down, in less than
3 seconds, press the front panel switch you
want to map.
The FX footswitch LED will flicker a couple of
times indicating that the switch has been
mapped.
From now on the selected footswitch will act
exactly in the same way as if you press the
related front panel switch.
Keys and presets can be assigned as wished
without limitation and in any order (again, except
the FOOTSWITCH / MIDI PROGRAM key). The
footswitch configuration is stored in the
footswitch itself, not in the amplifier. Resetting
the amplifier will not affect the footswitch
configuration as well.
The footswitch can be hot-swapped and
synchronises itself with the amplifier after
connection. However it is recommended to
connect the footswitch lead to the footswitch
side first and then connect it to the amplifier.
MIDI operation
Pressing the FOOTSWITCH / MIDI PROGRAM
switch twice puts the amplifier in MIDI waiting
mode, the LED will flash until a valid MIDI
program change command is received.
On reception of a MIDI program change
command the amplifier stores the current status
(Channel + FX + Reverb + Master Settings) in
the MIDI program number received. It is
possible to store up to 128 different MIDI
presets.
To exit this status without waiting for incoming
MIDI data press the FOOTSWITCH / MIDI
PROGRAM switch again.
Note about MIDI channels: By default the
amplifier is configured to listen to MIDI channel
#1 but it can be changed to listen to any of the
16 MIDI channels as follows:
Switch the amplifier off (Power switch, not
Standby).
Press and hold the FOOTSWITCH / MIDI
PROGRAM switch.
Switch the amplifier on (Power switch).
Release the FOOTSWITCH / MIDI PROGRAM
switch, the LED will start to flash.
Send ANY MIDI command using your MIDI
pedalboard or any other MIDI equipment.
The amplifier will detect which channel came in
and configure itself to listen to that MIDI channel
only. From now on any MIDI preset you had
previously stored will be activated only on the
new channel regardless of what channel you
used before, this allows a fast reconfiguration
should there be a MIDI conflict with any other
outboard equipment.
If you want to exit the MIDI channel selection
without any action press the
FOOTSWITCH / MIDI PROGRAM switch while
waiting for MIDI data.
Front Panel Operation
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Marshall-JVM410-Series

Zoeken resetten

  • Hi everybody, would anybody be able to tell me exactly how to program a Marshall JVM410H with a TC Electronics G-Major? The first model G-Major I believe it is. Thanks a lot. Greetings, Chris Gesteld op 12-11-2022 om 09:52

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marshall JVM410 Series bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marshall JVM410 Series in de taal/talen: Engels als bijlage per email.

De handleiding is 1,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info