442747
6
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
8 9
1. Mains Input Connector
Your AVT is provided with a detachable mains
(power) lead which is connected here. The
specific mains input voltage rating that your
amplifier has been built for is shown on the back
panel. Before connecting for the first time,
please ensure that your electricity supply is
compatible with your amplifier. If you have any
doubt, please seek advice from a qualified
technician. Your Marshall dealer will help in this
respect.
2. Loudspeaker Jack Sockets
a) AVT150X
There are two speaker jacksockets on the
AVT150X. The one marked Internal (8 Ohm) is
where the output of the AVT power amplifier is
connected to its internal 8 Ohm Celestion
loudspeaker.
When an extension speaker is connected to the
other output (marked Extension) the full power
of the 150W power amplifier is unleashed.
Please note that only an extension cabinet rated
at 8 Ohms should be used.
This will provide a parallel load with the Internal
Speaker of 4 Ohms minimum.
b) AVT150HX
The AVT150HX has two loudspeaker outputs.
The one marked ‘Extension 8
is for
connection to a single 8 Ohm cabinet. The
output marked ‘Extension 8/4 can either be
used for connection to a second 8 Ohm speaker
cabinet, or to drive a single 4 Ohm cabinet.
WARNING:
Always provide the AVT with a load equal to, or
greater than, 4 Ohms.
Note: Two 8 cabinets connected in
parallel = 4
3. Footswitch
For connection of the supplied Stage Foot
Controller (PEDL-10031). This sturdy 6-way
Marshall footswitch allows instant selection of
the 4 channels, plus the two DFX modes. It also
features LEDs to indicate status.
4.
Headphones
The headphones output is fully emulated using
an improved version of the circuitry found on the
industry standard JMP-1. Turning the Master
Volume (20) to zero will provide silent practice.
5. Emulated Line Output
This jack socket carries a specially treated
output signal from your AVT that accurately
emulates the sonic signature of a Marshall 4x12
cabinet. This unerringly accurate emulation
circuitry is Marshall's most advanced to date
and was developed via countless hours of
technical research, playing, listening and fine-
tuning. This output can be used in both live
performance and recording situations to achieve
authentic guitar amp tones, without having to
use a microphone. Turn down the Master
Volume (20) for silent recording.
FX Loop
As already mentioned, the AVT150X and
AVT150HX both boast a Mono Parallel FX loop
for connection with external effects units. In
addition to the FX Mix controls on the front
panel (see ‘Front Panel Features’, point 22) this
FX loop comprises of an FX Send jack, an FX
Return jack and an FX level control button.
6. FX Return
For connection to the output of your external
effects device.
7. FX Level
This should be set to match the level of the
processor being used (generally -10dB for a
stomp box, +4dB for a professional, rack unit).
8. FX Send
For connection to the input of the external
device being used.
* FX Loop Hints:
a) Always use high quality, shielded patch
cables.
b) If the processor being used has an input level
control, ensure it is set correctly.
c) Time based effects (delays & reverbs) and
modulation effects (chorus, flange, phase, etc.)
are ideal for use in a Parallel FX loop.
d) Certain stomp box effects such as Wah,
distortion, overdrive and fuzz were designed
specifically for use in front of the amp and sound
best when used that way. This said, tonal beauty
is in the ears of the beholder so, if such a pedal
sounds great to you when used in an FX loop
then go for it! Sometimes, there are no rules...
!!
AVT150X & AVT150HX Rear Panel Features AVT275X Rear Panel Features
1. Mains Input Connector
Your AVT is provided with a detachable mains
(power) lead which is connected here. The
specific mains input voltage rating that your
amplifier has been built for is shown on the back
panel. Before connecting for the first time, please
ensure that your electricity supply is compatible
with your amplifier. If you have any doubt, please
seek advice from a qualified person. Your
Marshall dealer will help in this respect.
2. Loudspeaker Jack Sockets
These connect the internal loudspeakers to the
stereo power amplifier outputs.
WARNING:
Always provide both with a load equal to, or
greater than 8 Ohms.
3. Footswitch
For connection of the supplied stage foot
controller (PEDL-10031). This sturdy 6 way,
Marshall footswitch allows instant selection of
the 4 channels, plus the two DFX modes. It also
features LEDs to indicate status.
4. Headphones
The headphones output is fully emulated using
an improved version of the circuitry found on the
industry standard JMP-1. Turning the Master
Volume (20) to zero will provide silent practice.
5. Emulated Line Outputs (L, R)
This pair of stereo jack sockets carries a
specially treated output signal from your AVT
that accurately emulates the sonic signature of a
Marshall stereo 4x12 cabinet. This unerringly
accurate emulation circuitry is Marshall's most
advanced to date and was developed via
countless hours of technical research, playing,
listening and fine-tuning. This output can be
used in both live performance and recording
situations to achieve authentic guitar amp tones,
without having to use a microphone. Turn down
the Master Volume (20) for silent recording.
FX Loop
As previously mentioned, the AVT275X boasts a
Parallel FX loop for connection with external
effects units. In addition to the FX Mix controls
on the front panel (see ‘Front Panel Features’,
point 22) this FX loop comprises of an FX Send
jack, two FX Return jacks, Left & Right, and an
FX level control button.
6. FX Return Left & Right
For connection with the stereo output of your
external effects device - left goes to left and,
wait for it, right goes to right.
Note: when using a mono output device use the
Right (R) FX return as indicated.
7. FX Level
This should be set to match the level of the
processor being used (-10dB for a stomp box,
+4dB for a professional, rack unit).
8. FX Send
For connection with the input of the external
device being used.
* FX Loop Hints:
a) Always use high quality, shielded patch
cables.
b) If the processor being used has an input level
control, ensure it is set correctly.
c) Time based effects (delays & reverbs) and
modulation effects (chorus, flange, phase, etc.)
are ideal for use in a Parallel FX loop.
d) Certain stomp box effects such as Wah,
distortion, overdrive and fuzz were designed
specifically for use in front of the amp and sound
best when used that way. This said, tonal beauty
is in the ears of the beholder so, if such a pedal
sounds great to you when used in an FX loop
then go for it! Sometimes, there are no rules...
!!
ENGLISH
ENGLISH
Follow all instructions and heed all warnings
KEEP THESE INSTRUCTIONS !
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marshall AVT150X, 150HX, 275X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marshall AVT150X, 150HX, 275X in de taal/talen: Engels als bijlage per email.

De handleiding is 2,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info