168195
6
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
8. MODE SELECTION / MUTE CONTROL
a) Briefly press this button to select Radio (TUNER) or Auxiliary Input (AUX) mode.
b) When pressing the button for more than 2 seconds, it will mute volume control and “MUTE ON” will appear on the display.
9.
You can enjoy RDS advantages on FM radio as following.
l Program Service Name (PS) : When an RDS station is received, station's name will appear on the display.
l Traffic Program (TP) : When station with traffic program is received, “TP” indicator will appear on the display.
l Alternative Frequencies (AF) : The unit continuously checking the signal strength of alternative frequencies for the tuned
radio station. Every time that new alternative frequency is stronger than current station, it automatically switch over to the
new frequency and new frequency will be displayed for 1-2 second. When the button pressed short, AF switching mode
is selected and the state of AF switching mode will appear on the display as following.
-RDS indicator on : AF mode is on and RDS signal is received.
-RDS indicator off : AF mode is off.
-RDS indicator flashing : AF switching mode is selected but RDS signal is not received yet.
l Enhanced Other Networks (EON): An RDS service where the broadcaster links some stations together. When tuned to a
station which is linked to others by EON, the radio is capable of receiving Traffic Announcement from the linked stations.
l Regional Program (for some countries only) : When tuned to a regional program, the radio will stay tuned to that
particular regional program as long as possible. If you drive out of the coverage area and the regional program becomes
very weak, the radio may tune to another regional program from the same network. To activate the regional program
function, pressing the button more than 2 seconds until “REG ON” appear on the display. To switch off the regional
program function, pressing the button more than 2 seconds until “REG OFF” appear on the display.
RDS (RADIO DATA SYSTEM) CONTROL
10.
Press the button to select TA mode on/off. When TA mode is on, “TA” indicator will appear on the display and the radio is
able to receive traffic announcements on the same stations or stations linked via EON with Traffic Program (TP). The TA
mode can work as following.
l If the volume setting is very low, volume level will be raised temporarily during traffic announcement and back to
original volume level at the end of traffic announcement.
l Temporary switch over to an EON linked program when EON detects a traffic announcement on that other program.
l If the radio is muted, it will be de-muted for the duration of the traffic announcement.
TA (TRAFFIC ANNOUNCEMENT) CONTROL
11. PTY (PROGRAMME TYPE NAME) CONTROL
There are 2 series of programme type (PTY) available for PTY search tuning. Pressing PTY button once or twice and then
pressing any Station Preset Button (1-6) until the desired PTY code appears on the display. The radio will stop on station
transmitting the selected PTY code. Next PTY searching can be activated by repeating the same procedure. During
programme type searching, PTY button can be pressed to stop searching and the radio will back to the original station.
“PTY NONE” will appear on the display if the selected PTY code is not receivable.
12. VOLUME/SELECTION BUTTON (“VOL/SEL”)
Rotate the button anti-clockwise to decrease, or clockwise to increase volume level.
AUDIO LEVEL CONTROL (WHEN PUSHING ONE AFTER ANOTHER)
Press this button shortly one after another to show VOL/BAS/TRE/BAL/FAD control.
lVOLUME - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase volume level.
lBASS - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase bass level.
lTREBLE - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase treble level.
lBALANCE - Press this button once, then rotate anti-clockwise or clockwise to level balance of speaker right and left.
lFADER - Press this button once, then rotate anti-clockwise or clockwise to level fader of speaker front and rear.
AUDIO/SETTING SELECT (HOLD MORE THAN 2 SECONDS)
When pressing the button for more than 2 seconds, it activates as unit setting selection in cyclical mode as following. The
unit setting can be changed by rotating the button clockwise or anti-clockwise.
lTA SEEK / TA ALARM
lMASK DPI / MASK ALL
lRETUNE-S / RETUNE-L
lDSP OFF / POP M / ROCK M / CLASS M / FLAT M
lLOUD OFF / LOUD ON
lSCROLL 1 / SCROLL 2 (display showing from left to right/right to left direction)
lBEEP ON / BEEP OFF (not available for this model)
lSTEREO / MONO
lDX / LOCAL
13/14. MANUAL UP/DOWN TUNING CONTROL
On radio mode, pressing the button for more than 1 seconds, it will tune one frequency step higher or lower.
15. STATION PRESET BUTTON (1-6)
The PRESET BUTTONS on the unit are used to store station frequencies which you may wish to recall. Each preset button
can store FM1, FM2, FM3, MW1, MW2 band station frequency. Pressing the button momentarily recalls the station frequency
which was memorized. There are 6 preset buttons, giving you capability of storing 18FM / 12MW.
NOTE: When the preset button to be memorized is kept pressed for more than 2 seconds, the receiving station frequency
will be stored in the button pressed. After this, the memorized station can be recalled by pressing the button once.
GB-3
(BLUE)
(WHITE)
(PURPLE/BLACK)
(WHITE/BLACK)
RIGHT
SPEAKER
LEFT
SPEAKER
WHITE/BLACK
PURPLE/BLACK
ORANGE
BLACK
GROUND
POWER
ANTENNA
ANTENNA
FUSE 3A
FUSE 3A
MEMORY
IGNITION
RED
YELLOW
BLUEWHITE
17. RESET BUTTON
The RESET button is located on the front of main panel.
It is recessed in order to prevent accidental engagement,
and can be activated with the tip of a ball-point pen or any similar pointed object. This reset circuitry is provided in order
to protect the unit's microprocessor, and should only be activated under the following conditions :
a) Initial installation after all wiring is completed.
b) Abnormal operation is encountered such as numerical indication on display is erratic.
c) Whenever the reset button is activated, all preset memory content will be erased and must be reprogrammed.
16. AUXILIARY INPUT
Press MODE button (8) until the “AUX” mode is
shown on display. The unit is ready to play songs
on an external audio device through the auxiliary
input directly on the front panel.
P/N:570-D61202-01
DASHBOARD
CONSOLE
METAL
MOUNTING STRIP
MOUNTING CASE
SELF-TAPPING
SCREW
HEXAGON SCREW
SPRING WASHER
PLAIN WASHER
WIRE CONNECTION
INSTALLATION
UNIT REMOVAL
1. Remove Front Control Panel.
2. Slightly insert the key into the slot and gently
to release.
3. Separate the mounting case from the unit.
Keep removal keys in a safe place as you
may need for future removal of unit.
CAUTION :
Do not connect the speaker wires to chassis or car body. Each speaker wire cannot be soldered together with other
wires. Otherwise, the unit will be damaged and warranty will be void.
GB-4
AUX
PRESET
EQ
MOBILE RADIO
Spectrum
D
i
s
p
l
ay
*AUXILIARY INPUT*
Compatible with
REMOVAL KEY
RCA
AUDIO
OUTPUT
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marquant mcr 1255 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marquant mcr 1255 in de taal/talen: Nederlands, Engels, Frans als bijlage per email.

De handleiding is 0,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info