494340
6
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
2. Plug the required IR Extender Cables (with IR LEDs or an IR Blaster) into the IR
Module via the connection ‘Emitters’ or ‘Emitters/Blasters’.
3. Self-adhesive film is provided with the IR LEDs and IR Blaster. This can be used
to easily affix the IR LEDs or IR Blaster in the correct position.
Ensure that the IR Extender Cable’s LEDs are stuck precisely onto the A/V
device’s infrared sensor. The exact position can easily be located by shining
a torch on them.
First test the position and working of the IR LEDs before fixing them per-
manently to the IR window of your A/V equipment.
If you use only one of the 2 LEDs, then leave the second IR LED unused.
Never remove it from the IR extension cable!
4. Now connect the IR Receiver to the IR Module, check the correct position and
the colours of the wires when doing so.
Place the supplied IR receiver in such a way that it is visible for your infra-
red remote control and if possible not in the vicinity of potential sources
of disturbance like direct sun light, TL lighting, energy saving lamps etc.
The infrared LED indicator on the IR receiver lights up or flashes when it
receives an infrared signal. Use the LED indicator to place the IR receiver
in the place with the least interference (LED indicator is not activated or
only faintly lights up).
Because of the supplied self-adhesive strip installation is possible almost
everywhere. Experiment for the correct place before you fix the IR recei-
ver definitively.
The adhesive strip can cause discoloration on certain surfaces or leave
glue remnants by removal.
5. Connect the power adapter to the ‘POWER’ connector on the IR Module and
plug the adapter into a socket (100-240V 50/60Hz).
See appendix on page 40/41 for more example installations.
4. FREQUENTLY ASKED QUESTIONS
Bad (or no) infrared return signal
Both the built-in and separate IR Receivers have reception sensitivity of
around 10 metres with an aperture angle of 90 degrees. Range is also depen-
dent on the remote control used. The IR reception indication LED in the IR
Receiver will light up when it receives an IR signal.
Check whether the power adapter is connected to the IR System Module.
Ensure that the IR Receiver and the IR Extender Cable are correctly connected
and that these are plugged in properly.
Try to avoid as many sources of disruption as possible, eg. direct sunlight,
fluorescent lighting, energy-saving bulbs and similar. These may have a nega-
tive impact upon the effectiveness of the system.
Some IR windows from set-top and satellite boxes are very sensitive and are
easily disrupted. These devices then receive too much infrared light and will
either work badly or not work at all. Relocate the IR LED or IR Blaster so that
less infrared light is received via the IR window.
6 © MARMITEK
IRCP200_UG_80x120 12-01-2010 14:53 Pagina 6
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek IR Control Pro System bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek IR Control Pro System in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info