494334
4
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
19
home automation modules & components
Connection of the Marmitek X-10 module to the wrong mains
voltage.
Opening of the Marmitek X-10 module's housing (with the
exception of types RFIX and IRIX that may be opened for
installation purposes).
Modification or repair of the Marmitek X-10 module or wiring
or any attempt to do so.
The Marmitek X-10 module becomes defective as a result of
connecting potential to the potential-free connecting wires of
the Marmitek X-10 module.
Defects resulting from rough handling of the Marmitek X-10
module or
Defects caused by using the wrong fuses or bridging fuses.
Limitation of liability
Except in the event of liability arising from the law, Marmitek is
not liable for direct damage, material damage or damage to
persons, including consequential damage.
Marmitek is not liable for any indirect damage, immaterial
damage or consequential damage whatsoever, including but not
limited to loss of revenue, damage caused by interruption to
production, loss of profits, pure pecuniary damage etc.
20
Area of application for XANURA home automation
Marmitek is a home automation system that has been designed
to be used exclusively in the housing sector. The area of
application for Marmitek X-10 modules must therefore remain
restricted to residential buildings and the housing sector. It is
not permitted to use Marmitek X-10 modules in the open air or
in humid environments. The system is exclusively intended for
use under the following environmental conditions:
X-10™ home automation
Power supply 230 Vac, 50 Hz
Minimum ambient temperature 0 °C
Maximum ambient temperature 40 °C (*) (**)
Atmospheric pressure 86 pkA - 106 pkA
Relative air humidity (non-condensing) 30 tot 90%
(*) Marmitek X-10 modules are suitable for use in residential environments at
ambient temperatures normally not exceeding 35 °C, occasionally reaching 40
°C.
(**) The maximum load for dim and switch actuators also depends on the ambient
temperature. Please carefully read the instructions for load reduction of dim and
switch actuators before using the Marmitek X-10 modules. The instructions are
enclosed with the dim and switch actuators.
21
Before starting the installation
Before installing a module, you must make sure that the module
is suitable for the intended application. If in doubt, contact a
qualified installer, specialist or the manufacturer for advice.
Instructions for installation & connection of modules
22
Instructions for installation & connection of modules
General installation and connection instructions
PLEASE NOTE: Disregarding the following instruc tions
can considerably shorten the service life of the
Marmitek X-10 modules and will render the guarantee
void! It is recommended to use a certified installer.
1 Use of modules to be restricted to the housing sector
2 Always disconnect the power before installing modules
3 Install in junction box or distribution box (or box with
comparable properties), covered with a cover plate or
switching device.
4 Make sure the live and neutral connections are correct!
5 One module per junction box/distribution box
6 The temperature of the module in the box used may
increase by a max. of 10 °C.
7 Never cover modules with insulation material
8 Pay attention to the proximity of heat sources
9 Prevent potential-free connecting wires from coming into
contact with live components (insulate live components)
10 Do not use objects or force during installation
11 Tightening torque for screws - max. 0.5 Nm
12 Keep modules accessible for programming and maintenance
!
23
Always switch the power off before installing the module.
If the live and neutral wires are connected to the module in
reverse, 230 V will be released on one of the module's
potential-free connecting wires! Make sure that the live and
neutral wires are connected correctly to ensure your safety
and the safety of others, see Figure 1.
2
4
3
5
PROG.
N
L
DAIX
10
Figure 1.
Connect the live wire (2) to the L side of the Marmitek X-10 module, and the
neutral wire (3) to one of the neutral terminals.
Connect the other neutral terminal (4) of the Marmitek X-10 module to the neutral
of the wall socket.
Connect the dimmed output of the Marmitek X-10 module (5) to the live terminal of
the wall socket.
24
Instructions for installation & connection of modules
Marmitek built-in modules must be installed in a junction box or
distribution box.
Other enclosures comparable to junction boxes and distribution
boxes are permitted as long as they meet the following criteria:
In these enclosures, the Marmitek built-in module and other
built-in components or equipment should not cause a
temperature increase within the enclosure that exceeds 10 °C.
Thermal properties at least equal to those of a junction
box/distribution box.
Flame resistance at least equal to that of a junction
box/distribution box.
Only one Marmitek X-10 module to
be installed per junction
box/distribution box. Besides one
Marmitek X-10 module, no other
heat generating components may
be installed in the same junction
box. The installation of several
Marmitek X-10 modules in a single
junction box can lead to the
Marmitek X-10 modules
malfunctioning or becoming
prematurely defective.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek AFX3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek AFX3 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info