571043
7
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
PRE OUT jacks-These jacks deliver the output of
the Model 1060 preamplifier circuits to the rear
panel.
MAIN IN jacks-These are the input terminals of
the power amplifier section of the Model 1060.
1
J
Note: The PRE OUT and MAIN IN jacks are
normally bridged by two molded
RCA type pin
plug assemblies which are provided with each
Model 1060. These assemblies must remain intact
for normal operation of the unit. However, should
you intend to use such equipment as a graphic
equalizer, compressor/limiter, or expander, you I
may connect these instruments to your Model:
1060 by removing the bridging connections from
the rear panel PRE OUT and MAIN IN jacks and
connecting appropriate length shielded audio Ii
cables from your Model 1060 to your processing
equipment.
I
CHASSIS GROUND-This binding post provides a I
convenient "earth" ground point to eliminate
possible ground loops between the Model 1060 and
program sources.
Convenience Outlets -Two AC outlets
on the rear
panel are provided for powering associated com- ~
ponents of your system, such as power amplifiers,
tuners, tape recorders, record players, etc. The
right one is controlled by the front panel POWER,
switch. The UNSWITCHED outlet is not controlled
by the POWER switch. This outlet is for powering
a turntable or record changer that has its own
on-off switch.
OPERATION
Simplified Operating Procedures-When operating
the Model 1060 Stereo Consolefor the first time,
follow these simple directions, using Figure 3.
Later 0 n, you can take fu II advantage of the
instrument's versatility by learning to use the
remaining controls and adjustments.
I Step 1. Turn the volume control all the way to the
left (fully counter-clockwise), and set the balance
control to mid-position.
Step 2. Set MONO IN (L,R) pushswitch to the
OUT position.
Step 3. Set TAPE NON pushswitch
to the OUT
position.
Step 4. Set all treble, mid and bass controls to the
center position.
I' Step 5. Depressthe POWER $witch. The pilot light
at the right center of the panel will glow.
Step 6. Select the desired program source by
turning the selector switch to the appropriate
position-unless the desired program source is a
recorded tape to be played by the taperecorder
which is connected to the DIN type recorder jack
or TAPE INjacks. MIC,PHONO,TAPE,AUX 10r
AUX 2 may be sele~ted, by the selector switch.
The TAPE, TUNER or AUX 1 positions select the
program sources connected to the corresponding
input jacks on the rear panel.
I mic/aux 2 jacks-These jacks accept the standard
2-conductor phone
plug.
1. When one low level microphone (less than
100mV, such as a dynamic type) is connected
to the "L" jack of the mic/aux 2 jacks, place
the selector switch in the MIC position. The
sound can be heard through the left channel
loudspeaker. In this case depress the MONO IN
(L) pushswitch to listen the sound from both
channel loudspeakers. If the microphone is
connected to the IIR" jack, depress the MONO
IN (R) pushswitch to hear the sound through
both channel speakers and release the (R) push-
switch to listen the sound through R channel
speaker only.
4
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marantz Model 1060 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marantz Model 1060 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info