Handleiding Marantec Comfort RE2224 (pagina 5 van 52) (Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools)

742800

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

Unscrew the cover screws (Fig.12a). Raise the back by about 1 cm

then slide it out forwards (Fig.12b).

The lights on the cover are connected by two wires, discon-

nect the terminal or lay carefully the cover upside-down on the

external part (Fig.13).

Loosen the screw of the mechanical limit switches up to when they

can slide (Fig.14).

Release the gearmotor and open manually the leaf up to the

requested opening position.

Insert the pin completely into the rst free hole close to the leaf

(Fig.15).

Move the mechanical stop up to the stop limit on the pin head

(Fig.16a) and screw again the mechanical stop (Fig.16b).

In order to adjust the stop in opening, move the leaf up to the

requested opening position and insert the pin into the rst free hole

opposite to the leaf.

Move the mechanical stop on the stop limit on the pin head (Fig.16a)

and screw it again (Fig.16b).

4.2 - Adjusting the mechanical limit switch in opening

Switch-o the power supply.

Open the cover as shown on paragraph 4.2.

By using a screwdriver, release the bottom screw of the cover

(Fig.19a).

Remove the mask and pull out the led band (Fig.19b) .

In case of installation of the second motor, follow the above mentioned instructions for the mechanical mounting, for the electrical connec-

tions refer to the Fig.21.

Disconnect the plug connector (Fig.20a).

Connect the new led stripe and insert them into the mask.

Insert the mask by placing rst the seal side and then fastening it

with the screw (Fig.20b).

4.5 - Replacing led

4.4 - Mechanical and electronic connections of the second motor

4.1 - Installation

Before starting the installation, make sure that the product is intact

and that the packaging contains all the components shown in Fig.3.

Make sure that the mounting area is compatible with the overall

dimensions (Fig.1).

Check the allowed opening angle according to the xing points of the

brackets in Fig.4 and in the diagram in Fig.5.

Fig.6 is an example of a typical system:

- Operators (1)

- Photocells (2)

- Posts for photocells (3)

- Flashing light with integrated aerial (4)

- Key or digital switch (5)

Mounting

Measure the value C (Fig. 4) = distance between the rotation fulcrum

of the leaf and the pillar surface where the rear bracket will be xed.

Move manually the leaf up to the opening required (maximum 120°):

establish the value of the maximum opening angle of each leaf.

Mark on the diagram in Fig.5 the value C and trace an horizontal

line up to intersect the area that includes the angle value measured

before.

Trace some vertical lines on the intersection points between the

horizontal line and the area in order to nd the useful values for the

dimension A (g. 4).

Chose the value A in this range.

Mark on the pillar the value A and trace a vertical line in correspon-

dence (Fig.7a).

Mounting the motor bracket to the pillar

Draw a horizontal line on the pillar in line where the leaf bracket

should be xed (Fig.7b).

Position the bracket so that the inside of the bottom edge is alig-

ned with the horizontal line shown in Fig. 7b and x it with suitable

screws and washers (not supplied) (Fig.7c).

Secure the gearmotor to the post bracket using the screw and nut

provided (Fig.8). The motor can be turned in this phase to simplify

the electrical connections (4.3 Electrical connections).

An o-axis mounting can cause malfunctioning and damage

the automation system.

Mounting the motor bracket

Fix the curved arm to the motor arm using the pin and stop ring.

Fix the gate bracket to the curved arm using the pin but without the

stop ring (Fig. 9).

Move the gate leaf up to the maximum opening position. Release

the gearmotor (Fig.10)

Completely extend the arms, position the curved arm next to the leaf

of the gate and place the gate bracket on it. Holding with one hand

the bracket in contact with the leaf, try to make a complete opening

and closing movement (Fig. 11a).

Fix the gate bracket to the leaf with suitable screws (not supplied)

and x the pin using the stop ring (Fig. 11b).

An o-axis mounting can cause malfunctioning and damage

the automation system.

4.3 - Electrical connections

Insert the supply cable (Fig.17). Connect the wires of the supply

cable to the terminal following the electrical drawing in Fig. 18.

Proceed with the other connections following the control unit’s

instructions.

Replace the cover to its original position and fasten the two xing

screws.

4 - PRODUCT INSTALLATION

WARNING

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Marantec Comfort RE2224 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info