DeutschEnglish Seite 29
O
24
Verkabelungsplan
A Antrieb Comfort 150DC / 160DC
B Schuko-Steckdose 220V - 240V, 50 Hz (bauseitig)
C Elektronische Antenne
D Steuerung Comfort 150DC / 160DC
E Innentastatur Marantec Command Serie mit Verbindungsleitung
F Schlüsseltaster Marantec Command Serie
Schaltplan B-MC 150DC / 160DC
F1 Sicherung (max. 2,5A)
F2 Sicherung (max. 10A)
H1 Antriebsbeleuchtung
M1 Motor
S x) Hauptschalter oder Taster "Not-Aus"
(bauseitig)
S1 x) Taster "Impuls"
S21 Drehzahlsensor
S22 Referenzpunktsensor
X0 +) Netzsteckdose
X1 Netzzuleitung mit Stecker
Anschlußklemmen:
X2c Befehlsgeräte
Steckanschlüsse:
X10 externe Bedienelemente
X20 elektronische Antenne
externe Lichtschranke
Anschluß Zubehör:
W20 elektronische Antenne
XS10 -) externe Bedienelemente
Marantec Command Serie
Achtung:
Kleinspannung!
Fremdspannung an den Klemmen X2c, X10 bis X20 führt zur Zerstörung der
gesamten Elektronik.
Achtung:
Örtliche Schutzbestimmungen beachten!
Netz- und Steuerleitungen unbedingt getrennt verlegen.
O
25
+) bauseitig
x) falls vorhanden
-) Bei Anschluß Kurzschlußstecker entfernen
Page 36
Retractable up-and-over doors:
Special 102 adapter arm, item no. 564 865, and Special 601 photocell, item no. 564 266,
are required (not included in the supply package). Until the ceiling mounts are subsequently
fitted, support the motor housing using a trestle or other suitable object.
Before installing the operator, put the door locks out of operation.
Screw wall bracket (A) with boom to the top of the door surround or lintel centrally above
the door ensuring that the top edge of the door at its highest point of opening clears the
bottom edge of the boom by at least 10 mm (see pt. 10).
Fitting the adapter arm:
Screw support bracket (B) with 6 self-tapping screws to the centre of the top edge of the
door leaf (5 mm dia. drill). The support bracket and boom meet centre to centre.
Slot adapter arm (C) into support bracket (B) and using two angle plates (D),
screw to door cross strut (E).
Drill 5 mm dia. hole in the door cross strut (4x)
Drill 7 mm dia. hole in the adapter arm (2x)
Angle plates (D) are screwed to the adapter arm using two M6 x 10 screws
and hexagon nuts.
Open the door fully, connect carriage (F) and linking bar (G) to adapter arm (C)
observing the given dimensions. By lowering the carriage and extending the linking bar,
the door opening is enlarged. The linking bar may only be pulled out to the
extent that the internally located pressure rollers (H) do not abut against check screws (I).
Close the door and check that the minimum distance of 165 mm has not been exceeded.
To ensure optimum operation of the operator and door,
the door travel speed should be altered to 8 cm/s.
See point 11 of the Installation Instructions.
O
8
Bolt on 2 support straps (A) to the motor housing. Bend them according to site
requirements and saw off the projecting lengths (see pt. 10).
Attach one support strap to the centre of the boom.
O
9
Suspend the motor housing with boom from the ceiling, making sure that the top edge of the
door at its highest point of opening clears the bottom edge of the boom by 10 mm
(see pts. 6, 7 and 8). Install the ceiling mounts as constructional features of the garage allow
(note drill depth for wall plugs).
O
10
