Handleiding Makita rp 1110 c (pagina 6 van 52) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

426965

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Adjusting the depth of cut (Fig. 1)

Place the tool on a flat surface. Loosen the lock knob and

lower the tool body until the bit just touches the flat sur-

face. Tighten the lock knob to lock the tool body.

Turn the stopper pole setting nut counterclockwise.

Lower the stopper pole until it makes contact with the

adjusting bolt. Align the depth pointer with the “0” gradua-

tion. The depth of cut is indicated on the scale by the

depth pointer.

While pressing the fast-feed button, raise the stopper

pole until the desired depth of cut is obtained. Minute

depth adjustments can be obtained by turning the adjust-

ing knob (1 mm per turn.)

By turning the stopper pole setting nut clockwise, you

can fasten the stopper pole firmly.

Now, your predetermined depth of cut can be obtained by

loosening the lock knob and then lowering the tool body

until the stopper pole makes contact with the adjusting

bolt of the stopper block.

Nylon nut (Fig.2)

By turning the nylon nut, the upper limit of the tool body

can be adjusted. When the tip of the bit is retracted more

than required in relation to the base plate surface, turn

the nylon nut to lower the upper limit.

CAUTION:

• Since excessive cutting may cause overload of the

motor or difficulty in controlling the tool, the depth of cut

should not be more than 15 mm at a pass when cutting

grooves with an 8 mm diameter bit.

• When cutting grooves with a 20 mm diameter bit, the

depth of cut should not be more than 5 mm at a pass.

• For extra-deep grooving operations, make two or three

passes with progressively deeper bit settings.

• Do not lower the nylon nut too low or the bit will pro-

trude dangerously.

Stopper block (Fig. 3)

The stopper block has three adjusting hex bolts which

raise or lower 0.8 mm per turn. You can easily obtain

three different depths of cut using these adjusting hex

bolts without readjusting the stopper pole.

Adjust the lowest hex bolt to obtain the deepest depth of

cut, following the method of “Adjusting depth of cut”.

Adjust the two remaining hex bolts to obtain shallower

depths of cut. The differences in height of these hex bolts

are equal to the differences in depths of cut.

To adjust the hex bolts, first loosen the hex nuts on the

hex bolts with the wrench and then turn the hex bolts.

After obtaining the desired position, tighten the hex nuts

while holding the hex bolts in that desired position. The

stopper block is also convenient for making three passes

with progressively deeper bit settings when cutting deep

grooves.

Switch action (Fig. 4)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• Make sure that the shaft lock is released before the

switch is turned on.

To start the tool, depress the lock button and pull the

switch trigger. Release the switch trigger to stop.

For continuous operation, pull the switch trigger and then

depress the lock button further. To stop the tool, pull the

switch trigger so that the lock button returns automati-

cally. Then release the switch trigger.

After releasing the switch trigger, the lock-off function

works to prevent the switch trigger from being pulled.

Speed adjusting dial (Fig. 5)

For RP1110C

The tool speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the

direction of number 5. And lower speed is obtained when

it is turned in the direction of number 1.

This allows the ideal speed to be selected for optimum

material processing, i.e. the speed can be correctly

adjusted to suit the material and bit diameter.

Refer to the table for the relationship between the num-

ber settings on the dial and the approximate tool speed.

CAUTION:

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing the bit (Fig. 6 & 7)

CAUTION:

• Install the bit securely. Always use only the wrench pro-

vided with the tool. A loose or overtightened bit can be

dangerous.

• Do not tighten the collet nut without inserting a bit. It

can lead to breakage of the collet cone.

Insert the bit all the way into the collet cone. Press the

shaft lock to keep the shaft stationary and use the

wrench to tighten the collet nut securely.

A 8 mm or 6.35 mm collet cone is factory installed on the

tool. When using router bits with other shank diameter,

use the correct size collet cone for the bit which you

intend to use.

To remove the bit, follow the installation procedure in

reverse.

Number min

–1

1 8,000

2 12,000

3 16,000

4 20,000

5 24,000

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita rp 1110 c Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Makita rp 1110 c

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info