Handleiding Makita hr 4511 c (pagina 7 van 52) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

388908

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

Indicator lamp (Fig. 9)

The green power-ON indicator lamp lights up when the

tool is plugged. If the indicator lamp does not light up, the

mains cord or the controller may be defective. The

indicator lamp is lit but the tool does not start even if the

tool is switched on, the carbon brushes may be worn out,

or the controller, the motor or the ON/OFF switch may be

defective.

The red service indicator lamp lights up when the carbon

brushes are nearly worn out to indicate that the tool needs

servicing. After approx. 8 hours of use, the motor will

automatically be shut off.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side handle (Fig. 10)

CAUTION:

• Use the side handle only when chipping, scaling or

demolishing. Do not use it when drilling in concrete,

masonry, etc. The tool cannot be held properly with this

side handle when drilling.

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal. Just

loosen the clamp nut to swing the side handle to a desired

position. Then tighten the clamp nut securely. (Fig. 11)

Side grip (Fig. 12)

CAUTION:

• Always use the side grip to ensure operating safety

when drilling in concrete, masonry, etc.

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip

by turning it counterclockwise, swing it to the desired

position and then tighten it by turning clockwise.

Installing or removing the bit (Fig. 13)

Clean the bit shank and apply bit grease before installing

the bit.

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 14)

If the bit cannot be pushed in, remove the bit. Pull the

chuck cover down a couple of times. Then insert the bit

again. Turn the bit and push it in until it engages.

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out. (Fig. 15)

Bit angle (when chipping, scaling or

demolishing) (Fig. 16 & 17)

The bit can be secured at 12 different angles. To change

the bit angle, depress the lock button and rotate the

change lever so that the pointer points to the symbol.

Turn the bit to the desired angle.

Depress the lock button and rotate the change lever so

that the pointer points to the symbol. Then make sure

that the bit is securely held in place by turning it slightly.

(Fig. 18 & 19)

Depth gauge (Fig. 20)

The depth gauge is convenient for drilling holes of uniform

depth. Loosen the clamp screw and adjust the depth

gauge to the desired depth. After adjusting, tighten the

clamp screw firmly.

NOTE:

• The depth gauge cannot be used at the position where

the depth gauge strikes against the gear housing/motor

housing.

OPERATION

Hammer drilling operation (Fig. 21)

Set the change lever to the symbol.

Position the bit at the desired location for the hole, then

pull the switch trigger. Do not force the tool. Light

pressure gives best results. Keep the tool in position and

prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at an

idle, then remove the bit partially from the hole. By

repeating this several times, the hole will be cleaned out

and normal drilling may be resumed.

CAUTION:

• When the bit begins to break through concrete or if the

bit strikes reinforcing rods embedded in concrete, the

tool may react dangerously. Maintain good balance

and safe footing while holding the tool firmly with both

hands to prevent dangerous reaction.

Blow-out bulb (optional accessory)

(Fig. 22)

After drilling the hole, use the blow-out bulb to clean the

dust out of the hole.

Chipping/Scaling/Demolition (Fig. 23)

Set the change lever to the symbol.

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• This servicing should be performed by Makita

Authorized Service Centers only.

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. It should be

lubricated every time the carbon brushes are replaced.

Send the complete tool to Makita Authorized Service

Center for this lubrication service.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita hr 4511 c Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info