Handleiding Makita bhr 200 (pagina 7 van 16) (Nederlands, Engels)

386275

Verklein

Vergroot

Pagina terug

1/16

Pagina verder

Bit angle

(when chipping, scaling or demolishing)

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before changing the bit angle.

To change the bit angle, depress the lock button and

rotate the change lever so that the pointer points to the

symbol. Turn the bit to the desired angle. (Fig. 13)

Depress the lock button and rotate the change lever so

that the pointer points to the

symbol. (Fig. 14)

Then make sure that the bit is securely held in place by

turning it slightly.

Operation

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

• When operating overhead, always make sure the bat-

tery cartridge is locked securely so that it will not be

fallen out of the tool. If not, it may accidentally fall out of

the tool, causing injury to you or someone around you.

Hammer drilling operation (Fig. 15)

Set the change lever to the H symbol. Position the bit at

the location for the hole, then pull the trigger. Do not force

the tool. Light pressure gives best results. Keep the tool

in position and prevent it from slipping away from the

hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at an

idle, then remove from the hole. By repeating this several

times, the hole will be cleaned out.

CAUTION:

• When the bit begins to break through concrete or if the

bit strikes reinforcing rods embedded in concrete, the

tool may react dangerously. Maintain good balance and

safe footing while holding the tool firmly with both

hands to prevent dangerous reaction.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

As soon as the torque limiter actuates, switch off the tool

immediately. This will help prevent premature wear of the

tool.

Chipping/Scaling/Demolition (Fig. 16)

Set the change lever to the

symbol. Hold the tool

firmly with both hands. Turn the tool on and apply slight

pressure on the tool so that the tool will not bounce

around, uncontrolled. Pressing very hard on the tool will

not increase the efficiency.

Drilling operation (Fig. 17)

Use the optional drill chuck assembly. When installing it,

refer to “Installing or removing drill bit” described on the

previous page. You can drill up to 13 mm diameter in

metal and up to 27 mm diameter in wood.

Set the change lever so that the pointer points to the

symbol.

Use a cutting lubricant when drilling metals. The excep-

tion is brass which should be drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool perfor-

mance and shorten the service life of the tool.

• Never use “rotation with hammering” when the drill

chuck assembly is installed on the tool. The drill chuck

assembly may be damaged.

Blow-out bulb (Fig. 18)

Use the blow-out bulb to clean out the hole.

Dust cup (Fig. 19)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling opera-

tions. Attach the dust cup to the bit. The size of bits which

the dust cup can be attached to is as follows.

Foot

Remove the foot when you use the battery cartridge

B2417.

This will help to place the tool steady. (Fig. 20)

Install the foot when you use the battery cartridge B2430.

This will help to place the tool steady. (Fig. 21)

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work on

the tool.

Replacement of carbon brushes (Fig. 22& 23)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clearn and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

Bit diameter (mm)

Dust cup 5 6– 14.5

Dust cup 9 12– 16

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita bhr 200 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Makita bhr 200

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info