448668
13
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
13
7
3
4
E
To guarantee a troublefree operation of the oil pump the oil
guide groove (E/3) as well as the oil inlet bore in the guide bar
(E/4) must be cleaned in regular intervals.
Note:
After the saw has been turned off it is normal for residual chain
oil to drip from the oil feed system, the guide bar and the chain
for a time. This does
not constitute a defect!
Place the saw on a suitable surface.
H
Checking the chain brake
Do not work with the chain saw without first checking the
chain brake!
- Start the motor as described (make sure you have a good
footing, and place the chain saw on the ground in such a way
that the guide bar is free of contact).
- Grasp the tubular handle firmly with one hand and hold the
grip with the other.
- Switch on the motor and press the hand guard (H/7) in the
direction of the arrow
with the back of your hand until the
chain brake engages. The chain should stop immediately.
- Switch the motor off
Immediately and release the chain
brake.
IMPORTANT: If the saw chain does not stop instantly
when you carry out this test, do not under any circum-
stances use the saw! Take the chain saw to a MAKITA
service center.
Switching on the motor
5
6
F
7
G
- Plug in the saw.
- When switching on the electric chain saw always hold
it with both hands.
- Take the back handle with the right hand and the tubular
handle with the left hand. Hold the handles tightly with your
thumbs facing your fingers. The bar and chain must not be
in contact with any object.
- First depress the locking button (F/5) and then the power
switch (F/6). Then release the locking button (F/5).
- Attention: The chain starts running immediately. Keep
the power switch depressed as long as the motor is to run.
CAUTION:
Never lock the power switch in the ON position.
Switching off the motor:
- Release the power switch (F/6).
NOTE:
When the chain brake is actuated the power supply to the
motor will be cut off.
If the saw does not start when the ON/OFF switch (F/6) is
actuated, it will be necessary to release the chain brake.
- Pull the hand guard (G/7) firmly in the direction of the arrow
until you feel it catch.
IMPOTANT NOTE: Turning on machines causes transient
voltage dips. If the conditions of the power supply network are
unfavourable, there might be interference with other devices
on the same network. If the impedance of the network is lower
than 0,072 Ohms it can pressumed that no interference will
happen.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita UC 3001A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita UC 3001A in de taal/talen: Engels als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita UC 3001A

Makita UC 3001A Gebruiksaanwijzing - Deutsch - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info