Handleiding Makita TD 021D (pagina 5 van 40) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

448659

Verklein

Vergroot

Pagina terug

1/40

Pagina verder

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

• Always switch off the tool before insertion or removal of

the battery cartridge.

Installing or removing battery cartridge (Fig. 1)

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Lock lever (Fig. 2)

When the lock lever is in the locked position , the

switch cannot be actuated.

When the lock lever is in the unlocked position , the

switch can be actuated.

Switch action

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch actuates properly

and returns to the “OFF” position when released.

To start the tool, first move the lock lever to the unlocked

position to release the switch lever. (Fig. 3)

And then turn the switch to A side for clockwise rotation

or to B side for counterclockwise rotation. (Fig. 4)

Tool speed is increased by increasing rotation force on

the switch. Release the switch to stop.

CAUTION:

• Always check the direction of rotation before operation.

• Change the direction only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the lock lever in

the locked position .

Lighting up the front lamp

CAUTION:

• Do not look in the light or see the source of light

directly.

To start the tool, first move the lock lever to the released

position to release the switch. (Fig. 5)

To put on the light only, rotate the switch to the A or B

side a little.

To not only put on the light but also start the tool rotate

the switch to the A or B side more.

Release the switch to stop the lamp and tool. (Fig. 4)

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

ASSEMBLY

CAUTION:

• Always be sure that the lock lever is in the locked posi-

tion mark and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit or socket bit

Use only the driver bit or socket bit shown in the figure.

(Fig. 6)

Do not use any other driver bit or socket bit.

For European and North & South American coun-

tries, Australia and New Zealand

For other countries

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit.

(Fig. 7)

2. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit-piece and bit into the sleeve

as far as it will go. The bit-piece should be inserted

into the sleeve with its pointed end facing in. Then

release the sleeve to secure the bit. (Fig. 8)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

OPERATION

The tool can be used in two ways; a straight type and a

pistol type which is selectable according to the conditions

of workplace and screwdriving. (Fig. 9)

CAUTION:

• When bending the tool to use in the pistol type or

straightening to use in the straight type, do not hold the

bendable part of the tool. Failure to do so may cause

your hand and fingers to be pinched and injured by this

part.

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

(Fig. 10 & 11)

A=12mm

B=9mm

Use only these types of bits. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A= 17mm

B= 14mm

To install these types of bits, follow the

procedure (1).

(Note) Makita bits are these types.

A= 12mm

B= 9mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for install-

ing the bit.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita TD 021D Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info