78700
6
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
6
Speed adjusting dial (Fig. 4)
The rotating speed can be changed by turning the speed
adjusting dial to a given number setting from 1 to 5.
Higher speed is obtained when the dial is turned in the
direction of number 5. And lower speed is obtained when
it is turned in the direction of number 1. Refer to the table
below for the relationship between the number settings
on the dial and the approximate rotating speed.
CAUTION:
If the tool is operated continuously at low speeds
(speed adjusting dial: 1 3), the motor will get over-
loaded and heated up.
The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
The tools equipped with electronic function are easy to
operate because of the following features.
Constant speed control Electronic speed control for
obtaining constant speed. Possible to get fine finish,
because the rotating speed is kept constant even under
load condition.
Soft start feature Safety and soft start because of sup-
pressed starting shock.
High-Low speed setting button (Fig. 3 & 5)
The tool speed can be changed instantly while the tool is
running. Depress the “ I position for lowest speed and
depress “ II ” position for a given number setting. The tool
speed cannot be changed when the button is in “ I ” posi-
tion, even if you turn the speed adjusting dial. When you
turn the speed adjusting dial, always be sure that the but-
ton is depressed in “ II ” position.
FOR USE AS A POLISHER
Installing or removing pad (Fig. 6)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the pad.
Hold the spindle with the wrench so that it cannot revolve.
Then screw the pad onto the spindle all the way. (The
pad can be used to install the optional sponge pad.)
To remove the pad, follow the installation procedure in
reverse.
Installing or removing sponge pad (Fig. 7)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the sponge pad.
To install the sponge pad, first remove all dirt or foreign
matter from the pad. Install the sponge pad to the pad.
To remove the pad, pull off it from the pad slowly.
Installing or removing the wool bonnet
(Fig. 8, 9 & 10)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the wool bonnet.
Mount the rubber pad onto the spindle. Screw the lock
nut onto the spindle. Hold the spindle firmly with the
wrench and tighten the lock nut using the lock nut
wrench. Fit the wool bonnet over the rubber pad. Tie a
bow knot and tuck the knot and any loose strings
between the wool bonnet and the rubber pad.
To remove the wool bonnet, follow the installation proce-
dure in reverse.
Polishing operation by sponge pad/wool
bonnet (Fig. 11 & 12)
CAUTION:
Always wear safety glasses or a face shield during
operation.
Apply slight pressure only. Excessive pressure will
result in poor performance and premature wear to the
sponge pad/wool bonnet.
When polishing, keep the sponge pad/wool bonnet at an
angle of about 15° to the workpiece surface.
FOR USE AS A SANDER
Installing or removing abrasive disc
(Fig. 13 & 14)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the abrasive
disc.
Mount the rubber pad onto the spindle. Fit the abrasive
disc on over the rubber pad and screw the lock nut onto
the spindle. Hold the spindle firmly with the wrench and
tighten the lock nut using the lock nut wrench.
To remove the abrasive disc, follow the installation proce-
dure in reverse.
NOTE:
The rubber pad, abrasive disc, lock nut and lock nut
wrench are optional accessories.
Sanding operation (Fig. 15)
CAUTION:
Always wear safety glasses or a face shield during
operation.
Apply slight pressure only. Excessive pressure will
result in poor performance and premature wear to the
abrasive disc.
Never run the tool without the abrasive disc. You may
seriously damage the pad.
Keep the abrasive disc at an angle of about 15° to the
workpiece surface.
Number min
-1
(R.P.M.)
1–2 600–800
2–3 800–1,300
3–4 1,300–1,800
4–5 1,800–2,000
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita PV 7000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita PV 7000 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info