Handleiding Makita PJ7000 (pagina 7 van 48) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens)

598964

Verklein

Vergroot

Pagina terug

1/48

Pagina verder

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.

Adjusting the depth of groove (Fig. 1)

6 grooving depths can be preset according to the size of biscuit to be used.

Refer to the table below for the correspondence between the sizes marked on the stopper and the biscuit size. Fine

adjustments to the grooving depth can be made by turning the adjusting screw after loosening the hex nut. This may

become necessary after the blade has been resharpened a few times.

* With the rubber spikes removed.

012681

Angle guide (Fig. 2 & 3)

The angle guide height can be moved up and down to

adjust the position of the blade in relation to the top of the

workpiece.

To adjust the angle guide height, loosen the lock lever

down and rotate the knob until the pointer points to the

desired scale graduation marked on the angle guide.

Then tighten the lock lever up to secure the angle guide.

The scale on the angle guide indicates the distance from

the top of the workpiece to the center of the blade thick-

ness.

The angle guide is removable from the fence according

to the need of your work. To remove the angle guide,

loosen the lock lever and turn the knob clockwise until it

comes out of the upper end of the fence.

Fence (Fig. 4 & 5)

NOTE:

• Remove the angle guide according to the need of your

work when using the tool with the angle of the fence

adjusted to other than 0°. When you need to use the

angle guide under the above condition, be sure to

adjust the depth of groove to get a proper depth.

The angle of the fence can be adjusted between 0° and

90° (positive stops at 0°, 45° and 90°). To adjust the

angle, loosen the lock lever and tilt the fence until the

pointer points to the desired graduation on the angle

scale. Then tighten the lock lever to secure the fence.

When the fence is set at 90°, both the distance from the

center of the blade thickness to the fence and the dis-

tance from the center of the blade thickness to the bot-

tom of the blade cover are 10 mm.

Set plate (Fig. 6 & 7)

Use the set plate as shown in Fig. 6 & 7 when cutting

slots in thin workpieces.

Switch action (Fig. 8)

CAUTION:

• Before plugging in the tool, always check to see that

the slide switch actuates properly and returns to the

“OFF” position when the rear of the slide switch is

depressed.

• Switch can be locked in “ON” position for ease of operator

comfort during extended use. Apply caution when locking

tool in “ON” position and maintain firm grasp on tool.

To start the tool, slide the slide switch toward the “I (ON)”

position. For continuous operation, press the front of the

slide switch to lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing the blade (Fig. 9)

CAUTION:

• When installing the plate joiner blade, mount the inner

flange with the side marked “22” facing toward you.

To remove the blade, loosen the clamp screw and open

the blade cover. Push the shaft lock and loosen the lock

nut using the lock nut wrench. To install the blade, first

mount the inner flange.

Then mount the blade and the lock nut. Securely tighten

the lock nut using the lock nut wrench. Close the blade

cover and tighten the clamp screw to secure the blade

cover.

CAUTION:

• Use only Makita lock nut wrench provided to remove or

install the blade.

• Always check the depth of groove after replacing the

blade. Readjust it if necessary.

Dust bag (Fig. 10)

To attach the dust bag, fit it onto the dust nozzle. If the

dust bag becomes an obstacle to your work, turn the dust

nozzle to change the dust bag position.

When the dust bag is about half full, switch off and

unplug the tool. Remove the dust bag from the tool and

pull the bag’s fastener out. Empty the dust bag by tap-

ping it lightly to remove as much of the dust as possible.

NOTE:

• If you connect a Makita vacuum cleaner to your plate

joiner, more efficient and cleaner operations can be

performed.

Size on stopper 0 10 20 S D MAX

Biscuit size 0 10 20 — — —

Depth of groove 8 mm 10 mm 12.3 mm 13 mm 14.7 mm 20 mm

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita PJ7000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info