Handleiding Makita MT431 (pagina 7 van 44) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

598763

Verklein

Vergroot

Pagina terug

1/44

Pagina verder

Bevel cutting

CAUTION:

• Always be sure that the tool is switched off and

unplugged before tilting the base.

• Raise the dust cover all the way before making bevel

cuts.

With the base tilted, you can make bevel cuts at any

angle between 0° and 45° (left or right). (Fig. 7)

Loosen the bolt on the back of the base with the hex

wrench. Move the base so that the bolt is positioned in

the center of the cross-shaped slot in the base. (Fig. 8)

Tilt the base until the desired bevel angle is obtained.

The edge of the motor housing indicates the bevel angle

by graduations. Then tighten the bolt to secure the base.

(Fig. 9)

Front flush cuts (Fig. 10)

Loosen the bolt on the back of the tool base with the hex

wrench and slide the base all the way back. Then tighten

the bolt to secure the base.

Cutouts

Cutouts can be made with either of two methods A or B.

A) Boring a starting hole

For internal cutouts without a lead-in cut from an

edge, pre-drill a starting hole 12 mm or more in diam-

eter. Insert the blade into this hole to start your cut.

(Fig. 11)

B) Plunge cutting

You need not bore a starting hole or make a lead-in

cut if you carefully do as follows.

1. Tilt the tool up on the front edge of the base with

the blade point positioned just above the work-

piece surface. (Fig. 12)

2. Apply pressure to the tool so that the front edge of

the base will not move when you switch on the tool

and gently lower the back end of the tool slowly.

3. As the blade pierces the workpiece, slowly lower

the base of the tool down onto the workpiece sur-

face.

4. Complete the cut in the normal manner.

Finishing edges (Fig. 13)

To trim edges or make dimensional adjustments, run the

blade lightly along the cut edges.

Metal cutting

Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause significant blade wear.

The underside of the workpiece can be greased instead

of using a coolant.

Dust extraction (Fig. 14)

Clean cutting operations can be performed by connecting

this tool to a Makita vacuum cleaner. Insert the hose of

the vacuum cleaner into the hole at the rear of the tool.

NOTE:

• Dust extraction cannot be performed when making

bevel cuts.

Rip fence (optional accessory)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing accessories.

1) Straight cuts (Fig. 15 & 16)

When repeatedly cutting widths of 160 mm or less,

use of the rip fence will assure fast, clean, straight

cuts.

To install, insert the rip fence into the rectangular

hole on the side of the base with the fence guide fac-

ing down. Slide the rip fence to the desired cutting

width position, then tighten the bolt to secure it.

2) Circular cuts (Fig. 17 & 18)

When cutting circles or arcs of 170 mm or less in

radius, install the rip fence as follows.

Insert the rip fence into the rectangular hole on the

side of the base with the fence guide facing up.

Insert the circular guide pin through either of the two

holes on the fence guide. Screw the threaded knob

onto the pin to secure the pin.

Now slide the rip fence to the desired cutting radius,

and tighten the bolt to secure it in place. Then move

the base all the way forward.

NOTE:

• Always use blades No. B-17, B-18, B-26 or B-27 when

cutting circles or arcs.

Anti-splintering device for steel base

(optional accessory) (Fig. 19)

For splinter-free cuts, the anti-splintering device can be

used. To install the anti-splintering device, move the base

all the way forward and insert it between the two protru-

sions of the base.

NOTE:

• The anti-splintering device cannot be used when mak-

ing bevel cuts.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita MT431 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info