Handleiding Makita LS 1214L (pagina 21 van 120) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

448600

Verklein

Vergroot

Pagina terug

1/120

Pagina verder

CAUTION:

• Firmly tighten the knob clockwise so that the carriage

will not move during operation. Insufficient tightening

may cause unexpected kickback of the blade. Possible

serious PERSONAL INJURY may result.

2. Slide (push) cutting (cutting wide workpieces)

(Fig. 43)

Loosen the knob counterclockwise so that the carriage

can slide freely. Secure the workpiece with the vise. Pull

the carriage toward you fully. Switch on the tool without

the blade making any contact and wait until the blade

attains full speed. Press down the handle and PUSH

THE CARRIAGE TOWARD THE GUIDE FENCE AND

THROUGH THE WORKPIECE. When the cut is com-

pleted, switch off the tool and WAIT UNTIL THE BLADE

HAS COME TO A COMPLETE STOP before returning

the blade to its fully elevated position.

CAUTION:

• Whenever performing the slide cut, FIRST PULL THE

CARRIAGE TOWARD YOU FULLY and press down the

handle to the fully lowered position, then PUSH THE

CARRIAGE TOWARD THE GUIDE FENCE. NEVER

START THE CUT WITH THE CARRIAGE NOT FULLY

PULLED TOWARD YOU. If you perform the slide cut

without pulling the carriage fully or if you perform the

slide cut toward your direction, the blade may kickback

unexpectedly with the potential to cause serious PER-

SONAL INJURY.

• Never perform the slide cut with the handle locked in

the lowered position by pressing the stopper pin.

• Never loosen the knob which secures the carriage

while the blade is rotating. This may cause serious

injury.

3. Mitre cutting

Refer to the previously covered “Adjusting the miter

angle”.

4. Bevel cut (Fig. 44)

Loosen the lever and tilt the saw blade to set the bevel

angle (Refer to the previously covered “Adjusting the

bevel angle”). Be sure to retighten the lever firmly to

secure the selected bevel angle safely. Secure the work-

piece with a vise. Make sure the carriage is pulled all the

way back toward the operator. Switch on the tool without

the blade making any contact and wait until the blade

attains full speed. Then gently lower the handle to the

fully lowered position while applying pressure in parallel

with the blade and PUSH THE CARRIAGE TOWARD

THE GUIDE FENCE TO CUT THE WORKPIECE. When

the cut is completed, switch off the tool and WAIT UNTIL

THE BLADE HAS COME TO A COMPLETE STOP

before returning the blade to its fully elevated position.

CAUTION:

• Always be sure that the blade will move down to bevel

direction during a bevel cut. Keep hands out of path of

saw blade.

• During a bevel cut, it may create a condition whereby

the piece cut off will come to rest against the side of the

blade. If the blade is raised while the blade is still rotat-

ing, this piece may be caught by the blade, causing

fragments to be scattered which is dangerous. The

blade should be raised ONLY after the blade has come

to a complete stop.

• When pressing down the handle, apply pressure in par-

allel with the blade. If a force is applied perpendicularly

to the turn base or if the pressure direction is changed

during a cut, the precision of the cut will be impaired.

• Always set the sub-fence to the left position when per-

forming left bevel cuts.

5. Compound cutting

Compound cutting is the process in which a bevel angle

is made at the same time in which a miter angle is being

cut on a workpiece. Compound cutting can be performed

at angle shown in the table.

At the miter angle of left 45° and bevel angle of left

45°, workpieces up to 66 mm high and 170 mm wide

can be cut.

At the miter angle of right 45° and bevel angle of left 45°,

workpieces up to 66 mm high and 215 mm wide can be

cut.

At the miter angle of left and right 45° and bevel angle of

right 45°, workpieces up to 45 mm high and 215 mm

wide can be cut.

When performing compound cutting, refer to “Press cut-

ting”, “Slide cutting”, “Miter cutting” and “Bevel cut” expla-

nations.

6. Cutting aluminum extrusion

When securing aluminum extrusions, use spacer blocks

or pieces of scrap as shown in Fig. 45 to prevent defor-

mation of the aluminum. Use a cutting lubricant when

cutting the aluminum extrusion to prevent build-up of the

aluminum material on the blade.

CAUTION:

• Never attempt to cut thick or round aluminum extru-

sions. Thick aluminum extrusions may come loose dur-

ing operation and round aluminum extrusions cannot

be secured firmly with this tool. (Fig. 46)

7. Wood facing (Fig. 47)

Use of wood facing helps to assure splinter-free cuts in

workpieces. Attach a wood facing to the guide fence

using the holes in the guide fence and 6 mm screws.

See the figure concerning the dimensions for a sug-

gested wood facing.

CAUTION:

• Use straight wood of even thickness as the wood fac-

ing.

• When cutting workpieces from 115 mm to 120 mm

high, use a wood facing to prevent a portion of the

workpiece near the guide fence from being left uncut.

Example:

When cutting workpieces 120 mm high, use a wood fac-

ing with the following thickness.

Miter angle Bevel angle

Left and Right 45° Left and Right 0° – 45°

Left 47° Left 0° – 45° and Right 0° – 40°

Right 52° Left 0° – 30° and Right 0° – 45°

Miter angle Thickness of wood facing

0° Over 20 mm

Left and Right 45° Over 15 mm

Right 52° Over 15 mm

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita LS 1214L Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Makita LS 1214L

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info