448590
6
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
ENGLISH
Explanation of general view
1 Bolt
2 Center cover
3 Socket wrench
4 Safety cover
5 Loosen
6 Shaft lock
7 Arrow
8 Blade case
9 Arrow
0 Saw blade
q Flange
w Spindle
e Ring
r Flange
t Hex bolt
y Dust spout
u Elbow
i Dust bag
o Fastener
p Switch trigger
a Lever
s Turn base
d Kerf board
f Depth adjusting bolt
g Guide fence
h Pointer
j Miter scale
k Grip
l Clamp screw
; Vise arm
z Screw
x Workpiece
c Cutting line
v Groove
b Support
n Screw
m Wood facing
, Aluminum extrusion
. Spacer blocks
/ Bolt
¡ Wrench
Hex lock nut
£ Arm
¢ Wrench
Triangular rule
§ Hex bolts
Set plate
Wing bolt
ª Holder
º Wing bolt
œ Carrying grip
Limit mark
é Screwdriver
® Brush holder cap
Stopper pin
SPECIFICATIONS
Model LS1030
Blade diameter ............................................. 255 mm
Max. cutting capacities (H x W)
Cross cut (90°) .......... 70 x 126 mm or 89 x 89 mm
Miter cut (45°) ............. 70 x 89 mm or 89 x 63 mm
No load speed (RPM) ...................................... 4,600
Dimensions (L xWxH)........... 470 x 485 x 510 mm
Net weight ..................................................... 10.6 kg
Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and canonly be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Wear eye protection.
2. Do not operate saw without guards in place.
3. Don’t use the machine in the presence of
flammable liquids or gases.
4. Check the blade carefully for cracks or dam-
age before operation. Replace cracked or
damaged blade immediately.
5. Use only flanges specified for this machine.
6. Be careful not to damage the arbor, flanges
(especially the installingsurface) or bolt. Dam-
age to these parts could result in blade break-
age.
7. Make sure that the turn base is properly
secured so it will not move during operation.
8. For your safety, remove the chips, small
pieces, etc. from the table top before opera-
tion.
9. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
10. Make sure the shaft lock is released before the
switch is turned on.
11. Be sure that the blade does not contact the
turn base in the lowest position.
12. Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
13. Do not perform any operation freehand. The
workpiece must be secured firmly against the
turn base and guide fence during all opera-
tions.
14. Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
15. Never reach around saw blade.
16. Make sure the blade is not contacting the
workpiece before the switch is turned on.
17. Before using the machine on an actual work-
piece, let it run for a while. Watch for vibration
or wobbling that could indicate poor installa-
tion or a poorly balanced blade.
18. Wait until the blade attains full speed before
cutting.
19. Stop operation immediately if you notice any-
thing abnormal.
20. Do not attempt to lock the trigger in the on
position.
21. Shut off power and wait for saw blade to stop
before servicing or adjusting machine.
6
LS1030 (E) (’97. 3. 6)
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita LS 1030 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita LS 1030 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita LS 1030

Makita LS 1030 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Dansk, Svenska, Norsk, Suomi - 68 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info