Handleiding Makita LS 1018 (pagina 18 van 128) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

448595

Verklein

Vergroot

Pagina terug

1/128

Pagina verder

2. Slide (push) cutting (cutting wide workpieces)

(Fig. 39)

Loosen the locking screw counterclockwise so that the

carriage can slide freely. Secure the workpiece with

the proper type of vise. Pull the carriage toward you

fully. Switch on the tool without the blade making any

contact and wait until the blade attains full speed.

Press the handle down and PUSH THE CARRIAGE

TOWARD THE GUIDE FENCE AND THROUGH THE

WORKPIECE. When the cut is completed, switch off

the tool and WAIT UNTIL THE BLADE HAS COME

TO A COMPLETE STOP before returning the blade to

its fully elevated position.

WARNING:

• Whenever performing a slide cut, first pull the

carriage full towards you and press the handle all

the way down, then push the carriage toward the

guide fence. Never start the cut with the carriage

not pulled fully toward you. If you perform the slide

cut without the carriage pulled fully toward you

unexpected kickback may occur and serious personal

injury may result.

• Never attempt to perform a slide cut by pulling the

carriage towards you. Pulling the carriage towards

you while cutting may cause unexpected kickback

resulting in possible serious personal injury.

• Never perform the slide cut with the handle locked in

the lowered position.

• Never loosen the locking screw which secures the

carriage while the blade is rotating. A loose carriage

while cutting may cause unexpected kickback resulting

in possible in serious personal injury.

3. Miter cutting

Refer to the previously covered “Adjusting the miter

angle”.

4. Bevel cut (Fig. 40)

Loosen the lever and tilt the saw blade to set the bevel

angle (Refer to the previously covered “Adjusting the

bevel angle”). Be sure to retighten the lever firmly to

secure the selected bevel angle safely. Secure the

workpiece with a vise. Make sure the carriage is pulled

all the way back toward the operator. Switch on the

tool without the blade making any contact and wait

until the blade attains full speed. Then gently lower the

handle to the fully lowered position while applying

pressure in parallel with the blade and PUSH THE

CARRIAGE TOWARD THE GUIDE FENCE TO CUT

THE WORKPIECE. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS COME

TO A COMPLETE STOP before returning the blade to

its fully elevated position.

WARNING:

• After setting the blade for a bevel cut, before

operating the tool ensure that the carriage and

blade will have free travel throughout the entire

range of the intended cut. Interruption of the carriage

or blade travel during the cutting operation may result

in kickback and serious personal injury.

• While making a bevel cut keep hands out of the

path of the blade. The angle of the blade may confuse

the operator as to the actual blade path while cutting

and contact with the blade will result in serious

personal injury.

• The blade should not be raised until it has come to

a complete stop. During a bevel cut the piece cut off

may come to rest against the blade. If the blade is

raised while it is rotating the cut-off piece maybe

ejected by the blade causing the material to fragment

which may result in serious personal injury.

NOTICE:

• When pressing down the handle, apply pressure in

parallel with the blade. If a force is applied

perpendicularly to the turn base or if the pressure

direction is changed during a cut, the precision of the

cut will be impaired.

• Before bevel-cutting, an adjustment of the upper fence

and lower fence maybe required. Refer to the section

titled “Guide fence adjustment”.

CAUTION:

• Always remove the sub-fence R so that it does not

interfere any part of the carriage when performing right

bevel cuts.

5. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter angle

is being cut on a workpiece. Compound cutting can be

performed at the angle shown in the table.

When performing compound cutting, refer to “Press

cutting”, “Slide cutting”, “Miter cutting” and “Bevel cut”

explanations.

6. Cutting crown and cove moldings

Crown and cove moldings can be cut on a compound

miter saw with the moldings laid flat on the turn base.

There are two common types of crown moldings and

one type of cove moldings; 52/38° wall angle crown

molding, 45° wall angle crown molding and 45° wall

angle cove molding. See illustrations. (Fig. 41)

There are crown and cove molding joints which are

made to fit “Inside” 90° corners ((1) and (2) in Fig. A)

and “Outside” 90° corners ((3) and (4) in Fig. A).

(Fig. 42 & 43)

Measuring

Measure the wall length and adjust workpiece on table

to cut wall contact edge to desired length. Always

make sure that cut workpiece length at the back of

the workpiece is the same as wall length. Adjust cut

length for angle of cut. Always use several pieces for

test cuts to check the saw angles.

When cutting crown and cove moldings, set the bevel

angle and miter angle as indicated in the table (A) and

position the moldings on the top surface of the saw

base as indicated in the table (B).

Miter angle Bevel angle

Left and Right 0° - 45° Left and Right 0° - 45°

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita LS 1018 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info