Handleiding Makita LS 1017L (pagina 18 van 120) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

448594

Verklein

Vergroot

Pagina terug

1/120

Pagina verder

while cutting may cause unexpected kickback resulting

in possible in serious personal injury.

3. Miter cutting

Refer to the previously covered “Adjusting the miter

angle”.

4. Bevel cut (Fig. 39)

Loosen the lever and tilt the saw blade to set the bevel

angle (Refer to the previously covered “Adjusting the

bevel angle”). Be sure to retighten the lever firmly to

secure the selected bevel angle safely. Secure the

workpiece with a vise. Make sure the carriage is pulled

all the way back toward the operator. Switch on the

tool without the blade making any contact and wait

until the blade attains full speed. Then gently lower the

handle to the fully lowered position while applying

pressure in parallel with the blade and PUSH THE

CARRIAGE TOWARD THE GUIDE FENCE TO CUT

THE WORKPIECE. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS COME

TO A COMPLETE STOP before returning the blade to

its fully elevated position.

WARNING:

• After setting the blade for a bevel cut, before

operating the tool ensure that the carriage and

blade will have free travel throughout the entire

range of the intended cut. Interruption of the carriage

or blade travel during the cutting operation may result

in kickback and serious personal injury.

• While making a bevel cut keep hands out of the

path of the blade. The angle of the blade may confuse

the operator as to the actual blade path while cutting

and contact with the blade will result in serious

personal injury.

• The blade should not be raised until it has come to

a complete stop. During a bevel cut the piece cut off

may come to rest against the blade. If the blade is

raised while it is rotating the cut-off piece maybe

ejected by the blade causing the material to fragment

which may result in serious personal injury.

NOTICE:

• When pressing down the handle, apply pressure in

parallel with the blade. If a force is applied

perpendicularly to the turn base or if the pressure

direction is changed during a cut, the precision of the

cut will be impaired.

• Before bevel-cutting, an adjustment of the upper fence

and lower fence maybe required. Refer to the section

titled “Guide fence adjustment”.

5. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter angle

is being cut on a workpiece. Compound cutting can be

performed at the angle shown in the table.

When performing compound cutting, refer to “Press

cutting”, “Slide cutting”, “Miter cutting” and “Bevel cut”

explanations.

6. Cutting crown and cove moldings

Crown and cove moldings can be cut on a compound

miter saw with the moldings laid flat on the turn base.

There are two common types of crown moldings and

one type of cove moldings; 52/38° wall angle crown

molding, 45° wall angle crown molding and 45° wall

angle cove molding. See illustrations. (Fig. 40)

There are crown and cove molding joints which are

made to fit “Inside” 90° corners ((1) and (2) in Fig. A)

and “Outside” 90° corners ((3) and (4) in Fig. A).

(Fig. 41 & 42)

Measuring

Measure the wall length and adjust workpiece on table

to cut wall contact edge to desired length. Always

make sure that cut workpiece length at the back of

the workpiece is the same as wall length. Adjust cut

length for angle of cut. Always use several pieces for

test cuts to check the saw angles.

When cutting crown and cove moldings, set the bevel

angle and miter angle as indicated in the table (A) and

position the moldings on the top surface of the saw

base as indicated in the table (B).

In the case of left bevel cut

Table (A)

Table (B)

Example:

In the case of cutting 52/38° type crown molding for

position (1) in Fig. A:

• Tilt and secure bevel angle setting to 33.9° LEFT.

• Adjust and secure miter angle setting to 31.6°

RIGHT.

• Lay crown molding with its broad back (hidden)

surface down on the turn base with its CEILING

CONTACT EDGE against the guide fence on the

saw.

• The finished piece to be used will always be on the

LEFT side of the blade after the cut has been

made.

7. Cutting aluminum extrusion (Fig. 43 & 44)

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

Miter angle Bevel angle

Left and Right 0° - 45° Left 0° - 45°

Molding

position in

Fig. A

Bevel angle Miter angle

52/38° type 45° type 52/38° type 45° type

For inside

corner

(1)

Left 33.9° Left 30°

Right 31.6° Right 35.3°

(2)

Left 31.6° Left 35.3°

For outside

corner

(3)

(4) Right 31.6° Right 35.3°

Molding

position in

Fig. A

Molding edge against guide

fence

Finished piece

For inside

corner

(1)

Ceiling contact edge should be

against guide fence.

Finished piece will

be on the Left side

of blade.

(2)

Wall contact edge should be

against guide fence.

For outside

corner

(3)

Finished piece will

be on the Right

side of blade.

(4)

Ceiling contact edge should be

against guide fence.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita LS 1017L Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info