17
• Do not pull the switch trigger hard without pressing in
the lock-off button. This can cause switch breakage.
For European countries (Fig. 13)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push the lever to the left, press in the lock-off button and
then pull the switch trigger. Release the switch trigger to
stop.
For all countries other than European countries
(Fig. 14)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
WARNING:
• NEVER use tool without a fully operative switch trigger.
Any tool with an inoperative switch is HIGHLY DAN-
GEROUS and must be repaired before further usage.
• For your safety, this tool is equipped with a lock-off but-
ton which prevents the tool from unintended starting.
NEVER use the tool if it runs when you simply pull the
switch trigger without pressing the lock-off button.
Return tool to a Makita service center for proper repairs
BEFORE further usage.
• NEVER tape down or defeat purpose and function of
lock-off button.
Lighting up the lamps
(Fig. 15 & 16)
For Model LS1013F, LS1013FL only
CAUTION:
• This is not a rainproof light. Do not wash the light in
water or use it in a rain or a wet area. Such a conduct
can cause an electric shock and fume.
• Do not touch the lens of the light, as it is very hot while
it is lighted or shortly after it is turned off. This may
cause a burn to a human body.
• Do not apply impact to the light, which may cause dam-
age or shorted service time to it.
• Do not keep casting the beam of the light to your eyes.
This can cause your eyes to be hurt.
• Do not cover the light with clothes, carton, cardboard or
similar objects while it is lighted, which can cause a fire
or an ignition.
Push the upper position of the switch for turning on the
light and the lower position for off.
Move the light to shift an area of lighting.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of light, or it may lower
the illumination.
Kerf block (optional accessory) (Fig.17 & 18)
CAUTION:
• When using the kerf block, always cut at the same
miter angle.
• When changing the miter angle, use other kerf blocks.
• When performing bevel cuts, never use the kerf blocks.
Failure to do so splits the block, causing a serious injury
to operator.
When you use the kerf block at 90° cutting, you can splin-
ter-free cut in workpiece on the side of the guide fence
(height of the workpiece is up to 35 mm). Install the kerf
block onto the guide fence by means of the two screws.
(Adjust the guide fence and the kerf block so that they
contact their faces. Then tighten the screws securely.)
Laser beam action
For model LS1013L, LS1013FL only
CAUTION:
• Never look into the laser beam. Direct laser beam may
injure your eyes.
• LASER RADIATION, DO NOT STARE INTO THE
BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRU-
MENTS, CLASS 2M LASER PRODUCT.
To turn on the laser beam, press the upper position (I) of
the switch. Press the lower position (O) to turn off.
(Fig. 19)
Laser line can be shifted to either the left or right side of
the saw blade by adjusting the adjusting screw as fol-
lows. (Fig. 20)
1. Loosen the adjusting screw by turning it counter-
clockwise.
2. With the adjusting screw loosened, slide the adjust-
ing screw to the right or left as far as it goes.
3. Tighten the adjusting screw firmly at the position
where it stops sliding.
Laser line is factory adjusted so that it is positioned within
1 mm from the side surface of the blade (cutting posi-
tion).
NOTE:
• When laser line is dim and almost or entirely invisible
because of the direct sunlight in the indoor or outdoor
window-by work, relocate the work area to a place not
exposed to the direct sunlight.
Aligning the laser line (Fig. 21)
Laser line can be shifted to either the left or right side of
the blade according to the applications of cutting. Refer
to explanation titled “Laser beam action” regarding its
shifting method.
NOTE:
• Use wood facing against the guide fence when aligning
the cutting line with the laser line at the side of guide
fence in compound cutting (bevel angle 45 degrees and
miter angle right 45 degrees).
A) When you obtain correct size on the left side of work-
piece
• Shift the laser line to the left of the blade.
B) When you obtain correct size on the right side of
workpiece
• Shift the laser line to the right of the blade.
Align the cutting line on your workpiece with the laser
line.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Socket wrench storage (Fig. 22)
The socket wrench is stored as shown in the figure.
When using the socket wrench, pull it out of the wrench
holder. After using the socket wrench, return it to the
wrench holder.
