448572
10
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
10
Installing or removing saw blade
CAUTION:
When mounting the blade, make sure that the direction
of the arrow on the surface of the blade matches the
direction of the arrow on the blade case.
Use only the Makita socket wrench provided to install
or remove the blade. Failure to do so may result in
overtightening or insufficient tightening of the hex bolt.
This could cause a personal injury.
Do not touch the blade immediately after operation; it
may be extremely hot and could burn your skin.
To remove the blade, use the socket wrench to loosen
the hex bolt holding the center cover by turning it coun-
terclockwise. Raise the blade guard and center cover.
(Fig. 8)
Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt by turning counter-
clockwise. Then remove the hex bolt, outer flange and
blade. (Fig. 9)
To install the blade, mount the inner flange, saw blade,
outer flange and hex bolt onto the spindle in that order.
Tighten the hex bolt by turning clockwise while pressing
the shaft lock. Return the blade guard and center cover
to its original position. Then tighten the hex bolt clock-
wise to secure the center cover. Lower the handle to
make sure that the blade guard moves properly. (Fig. 10)
Securing workpieces
CAUTION:
Always set the vise nut to the right fully when securing
the workpiece. Failure to do so may result in insufficient
securing of the workpiece. This could cause the work-
piece to be ejected or cause damage to the blade.
By turning the vise handle counterclockwise and then
flipping the vise nut to the left, the vise is released from
the shaft threads and can be moved rapidly in and out. To
grip workpieces, push the vise handle until the vise plate
contacts the workpiece. Flip the vise nut to the right and
then turn the vise handle clockwise to securely retain the
workpiece. (Fig. 11)
Long workpieces must be supported by blocks of non-
flammable material on either side so that it will be level
with the base top. (Fig. 12)
OPERATION
Cutting operation
CAUTION:
Never attempt to cut workpieces less than 2 mm thick except pipe or workpieces which cannot be secured firmly with
the vise. The piece cut off may be caught by the blade, causing dangerous scattering of chips and/or damage to the
carbide-tips. Possible serious injury may result.
Do not apply excessive pressure on the handle when cutting. Too much pressure may result in overload of the motor,
decreased cutting efficiency and/or damage to the carbide-tips or blade itself.
Too little pressure on the handle may result in more sparks and premature blade wear.
Do not touch the blade, workpiece or cutting chips immediately after operation; they may be extremely hot and could
burn your skin.
If the blade stops during operation, makes an odd noise or begins to vibrate, switch off the tool immediately. Replace
cracked or damaged blade with a new one.
Do not cut aluminum, wood, plastics, concrete, tiles, etc.
Always use carbide-tipped saw blades appropriate for your job. The use of inappropriate saw blades may cause a
poor cutting performance and/or present a risk of personal injury.
Recommended Carbide-tipped saw blade & workpiece ranges
(NA ... Not applicable)
Standard blade may differ from country to country.
Carbide-tipped saw blades for metal cutting saw are not to be re-sharpened.
Diameter &
number of
teeth
Application
Applicable workpiece & thickness range
Angles Pipes Channels
Stainless
Pipes
Stainless
Angles
305 * 60 Mild Steel 4 mm or more 3 5 mm 4 mm or more NA NA
305 * 60
Mild Steel
(Lessened
Noise Type)
4 mm or more 3 5 mm 4 mm or more NA NA
305 * 78
Thin Mild
Steel
3–6mm 1.2–5mm 2mm or more NA NA
305 * 78
Stainless
Steel
3–6mm 1.2–5mm 4mm or more 1.2–5mm 3–4mm
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita LC 1230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita LC 1230 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 1,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita LC 1230

Makita LC 1230 Gebruiksaanwijzing - Nederlands, English - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info