448572
9
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
9
Cutting operation
CAUTION:
Never attempt to cut workpieces less than 2 mm thick except pipe or workpieces which cannot be secured firmly with
the vise. The piece cut off may be caught by the blade, causing dangerous scattering of chips and/or damage to the
carbide-tips. Possible serious injury may result.
Do not apply excessive pressure on the handle when cutting. Too much pressure may result in overload of the motor,
decreased cutting efficiency and/or damage to the carbide-tips or blade itself.
Too little pressure on the handle may result in more sparks and premature blade wear.
Do not touch the blade, workpiece or cutting chips immediately after operation; they may be extremely hot and could
burn your skin.
If the blade stops during operation, makes an odd noise or begins to vibrate, switch off the tool immediately. Replace
cracked or damaged blade with a new one.
Do not cut aluminum, wood, plastics, concrete, tiles, etc.
Always use carbide-tipped saw blades appropriate for your job. The use of inappropriate saw blades may cause
a poor cutting performance and/or present a risk of personal injury.
Recommended Carbide-tipped saw blade & workpiece ranges
(NA ... Not applicable)
Standard blade may differ from country to country.
Carbide-tipped saw blades for metal cutting saw are not to be re-sharpened.
Hold the handle firmly. Switch on the tool and wait until the blade attains full speed. Then lower the handle gently to
bring the blade close to the workpiece. When the blade makes contact, ease into the cut gently at first, then gradually
add pressure as the cutting position steadies. Your pressure on the handle should be adjusted to produce the mini-
mum amount of sparks.
When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP
before returning the handle to the fully elevated position. If the handle is raised while the blade is still rotating, the piece
cut off may be caught by the blade, causing dangerous scattering of chips. When cutting only part of the way into a
workpiece, raise the handle while the blade is rotating. Switching off during the cut may cause damage to the carbide-
tips as they contact the workpiece.
Cutting angles (Figs. 12 & 13)
Secure the workpiece in the vise as shown in Fig. 12-1,
and proceed to cut it. The saw blade life will be shortened
if the workpiece is cut as shown in Fig. 12-2.
CAUTION:
Do NOT cut the workpiece as shown in Fig. 12-3 since
this may cause it to be ejected from the vise, possibly
resulting in injury.
The saw blade is subjected to greater wear when the
area A in Fig. 12-2 is cut. Place a wooden block up
against the workpiece as shown in Fig. 13 so that the
saw blade will enter area A at an angle. This will help to
extend the saw blade life.
The allowable cutting dimensions are reduced when a
wooden block is used. Use a wooden block whose
dimensions are equivalent to the maximum allowable cut-
ting dimensions minus the dimensions of the workpiece
to be cut. This will further minimize the shortening of the
saw blade life.
Cutting pipes, squares and channels
(Figs. 14 & 15)
The saw blade is subjected to greater wear when the
areas A and B in Figs. 14-2 and 14-3 are cut. Place a
wooden block up against the workpiece as shown in
Fig. 15-2 so that the saw blade will enter areas A and B
at an angle. This will help to minimize the shortening of
the saw blade life.
The allowable cutting dimensions are reduced when a
wooden block is used. Use a wooden block whose
dimensions are equivalent to the maximum allowable cut-
ting dimensions minus the dimensions of the workpiece
to be cut. This will further minimize the shortening of the
saw blade life.
Cutting rectangles (Fig. 16)
Secure the workpiece in the vise as shown in Fig. 16-1,
and proceed to cut it.
CAUTION:
Do NOT cut the workpiece as shown in Fig. 16-2 since
this may cause it to be ejected from the vise, possibly
resulting in injury.
Diameter &
number of
teeth
Application
Applicable workpiece & thickness range
Angles Metal Pipes Channels
Stainless
Pipes
Stainless
Angles
305 * 60 Mild Steel 4 mm or more 3 5 mm 4 mm or more NA NA
305 * 60
Mild Steel
(Lessened
Noise Type)
4 mm or more 3 5 mm 4 mm or more NA NA
305 * 78
Thin Mild
Steel
3–6mm 1.2–5mm 2mm or more NA NA
305 * 78 Stainless 3–6mm 1.2–5mm 4mm or more 1.2–5mm 3–4mm
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita LC 1230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita LC 1230 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Makita LC 1230

Makita LC 1230 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Dansk - 52 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info