Handleiding Makita KP312S (pagina 5 van 44) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

599022

Verklein

Vergroot

Pagina terug

1/44

Pagina verder

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Adjusting depth of cut (Fig. 1)

The depth of cut can be adjusted within a range of 0 –

3.5 mm. Turn the knob on the front of the tool until the

pointer is aligned with the desired cutting depth on the

scale. Set the depth of a cut observing the maximum

depth which is limited by width according to the following

table.

Correlation of width of cut and maximum depth of

cut

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

"OFF" position when released.

For tool with lock button

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

For tool with lock-off button

To prevent the trigger from being accidentally pulled, a

lock-off button is provided. To start the tool, press the

lock-off button and pull the trigger. Release the trigger to

stop.

Overload protector (Option)

This tool is equipped with an overload protector which

automatically cuts out to break the circuit whenever

heavy work is prolonged. When it cuts out, inspect the

blade for damage or something wrong. After making sure

that there is nothing wrong with the tool, push the restart

button to resume operation.

Edge fence (Guide rule) (Fig. 3)

Edge fence is useful for minimizing a short run of cut by

cutting in a uniform width. The edge fence (guide rule) is

provided on the side of the tool. Press two pins for the

edge fence (guide rule) so that the edge fence appears.

Move the tool forward while keeping the flat surface of

the edge fence in contact with the side of the workpiece.

To return the edge fence to an original position, push it

upwards from its underside.

Foot (Fig. 4)

After a cutting operation, raise the back side of the tool

and a foot comes under the level of the rear base. This

prevents the tool blades to be damaged.

Guideline of cutting blade passage (Fig. 5)

Both ends of the front base are a guideline to show the

ends of cutting blades passage.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing planer blades (Fig. 6)

CAUTION:

• Tighten the blade installation bolts carefully when

attaching the blades to the tool. A loose installation bolt

can be dangerous. Always check to see they are tight-

ened securely.

• Handle the blades very carefully. Use gloves or rags to

protect your fingers or hands when removing or install-

ing the blades.

• Use only the Makita wrench provided to remove or

install the blades. Failure to do so may result in over-

tightening or insufficient tightening of the installation

bolts. This could cause an injury.

To remove planer blades on the drum, loosen the eight

installation bolts by only one full turn with the hex

wrench.

Then push and slide a planer blade sideways from the

belt side using the helm of the hex wrench.

To remove another planer blade, follow the same proce-

dure as above. (Fig. 7 & 8)

To install the blades, first clean out all chips or foreign

matter adhering to the drum or blades.

Insert the blade between the drum and the set plate from

the nozzle extraction side so that the blade will be cen-

tered from both ends of the drum or set plate.

First tighten the eight installation bolts lightly and evenly

shifting from the center bolts to the outward bolts with the

hex wrench.

And then, tighten all of the installation bolts securely.

Install another blade in the same manner as above.

(Fig. 9)

Width of cut Maximum depth of cut

0 – 150 mm 3.5 mm

150 – 240 mm 2 mm

240 – 312 mm 1.5 mm

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita KP312S Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info