448569
6
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
Thickness gauge combinations
Material
thickness
2.3 mm 2.5 mm 3.2 mm
Thickness gauge
combinations
1.0 + 1.5 1.0 + 1.5 1.5 + 2.0
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
‘‘OFF’ position when released.
To start the tool, simply pull the trigger. Release the
trigger to stop. For continuous operation, pull the
trigger and then push in the lock button. To stop the
tool from the locked position, pull the trigger fully, then
release it.
Permissible shearing thickness (Fig. 7)
The groove on the yoke serves as a thickness gauge
for shearing mild or stainless steel plate. If the mate-
rial fits within the groove, it is shearable.
The thickness of materials to be sheared depends
upon the type (strength) of the material. The maxi-
mum shearing thickness is indicated in the table
below in terms of various materials. Attempting to
shear materials thicker than indicated will result in tool
breakdown and/or possible injury. Keep within the
thickness shown below.
Max.cutting capacities mm ga
Steel up to 400 N/mm
2
3.2 10
Steel up to 600 N/mm
2
2.5 13
Steel up to 800 N/mm
2
1.5 17
Aluminum up to 200 N/mm
2
4.0 9
Holding material (Fig. 8)
The materials for cutting should be fastened to the work bench by means of workholders.
Shearing method (Fig. 9)
For smooth cuts, tip the tool slightly backward while advancing it.
Maximum cutting width
Stay within the specified maximum cutting width (A): Case of length 1,800 mm.
Mild steel
(thickness)
3.2 mm Under 2.3 mm
Max. cutting
width (A)
90 mm No limit
Stainless
(thickness)
2.5 mm Under 2.0 mm
Max. cutting
width (A)
70 mm No limit
Minimum cutting radius
Minimum cutting radius is 50 mm when cutting 2.3 mm mild steel.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Replacement of carbon brushes
(Fig. 10 & 11)
Replace carbon brushes when they are worn down to
the limit mark. Both identical carbon brushes should
be replaced at the same time.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by a
Makita Authorized Service Center
A
1,800
900
6
JS3200 (E) (’101. 1. 10)
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita JS 3200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita JS 3200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Makita JS 3200

Makita JS 3200 Gebruiksaanwijzing - Nederlands, English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info