448568
4
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
ENGLISH
Explanation of general view
1 Screw
2 Screwdriver
3 Center blade
4 Hex wrench
5 Side blade
6 Bolt
7 Pin
8 Slide switch
9 Limit mark
0 Brush holder cap
SPECIFICATIONS
Model JS1660 JS1670
Max. cutting capacities
Steel up to 400 N/mm
2
............................................ 1.6 mm/16 ga 1.0 mm/20 ga
Steel up to 600 N/mm
2
............................................ 1.2 mm/18 ga 0.7 mm/23 ga
Steel up to 800 N/mm
2
............................................ 0.8 mm/22 ga 0.5 mm/26 ga
Aluminum up to 200 N/mm
2
.................................... 2.5 mm/13 ga 2.5 mm/13 ga
Min. cutting radius ...................................................... 30 mm
Strokes per minute ..................................................... 4,500 4,500
Overall length ............................................................. 304 mm 306 mm
Net weight ................................................................... 1.3 kg 1.3 kg
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phaseAC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.
ADDITIONAL SAFETY RULES ENB011-2
1. Hold the tool firmly.
2. Secure the workpiece firmly.
3. Keep hands away from moving parts.
4. Edges and chips of the workpiece are sharp.
Wear gloves. It is also recommended that you
put on thickly bottomed shoes to prevent
injury.
5. Do not put the tool on the chips of the work-
piece. Otherwise it can cause damage and
trouble on the tool.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8. Do not touch the blade or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
9. Avoid cutting electrical wires. It can cause
serious accident by electric shock.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Adjusting the blade clearance (Fig.1&2)
For JS1660 Only
Important: Always be sure that the tool is switched off
and unplugged before adjusting the blade clearance.
Adjust the clearance between the side blade and the
center blade according to the thickness of the work-
piece.
First use a screwdriver to loosen the screw.
Then use the hex wrench to adjust the clearance by
tightening or loosening the bolt. There may be a slight
difference between clearances (A) and (B).
Check the smaller clearance with the thickness gauge
and adjust it.
When using the thickness gauge to adjust the blade
clearance, refer to the table below.
Workpiece thickness
(mm)
Marking on
thickness gauge
Less than 0.8 0.5
0.8 1.3 1.0
More than 1.3 1.5
After adjusting the clearance, tighten the screw
securely.
Lubrication (Fig. 3)
Before operation, lubricate the contact point of the
center blade and the pin. To keep good cutting
performance, also use a cutting lubricant from time to
time during operation.
4
JS1660/JS1670 (E) (’101. 1. 12)
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita JS 1670 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita JS 1670 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Makita JS 1670

Makita JS 1670 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Dansk, Svenska, Norsk, Suomi - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info