Handleiding Makita HR2630T (pagina 9 van 76) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens)

599668

Verklein

Vergroot

Pagina terug

1/76

Pagina verder

Grasp the change cover of the quick change drill chuck

and turn the change cover line to the symbol until a

click can clearly be heard.

Selecting action mode

CAUTION:

• Do not rotate the action mode changing knob when the

tool is running. The tool will be damaged.

• To avoid rapid wear on the mode change mechanism,

be sure that the action mode changing knob is always

positively located in one of the three action mode

positions.

Rotation with hammering (Fig. 8)

For drilling in concrete, masonry, etc., rotate the action

mode changing knob to the symbol. Use a tungsten-

carbide tipped bit.

Rotation only (Fig. 9)

For drilling in wood, metal or plastic materials, rotate the

action mode changing knob to the

m symbol. Use a twist

drill bit or wood bit.

Hammering only (Fig. 10)

For chipping, scaling or demolition operations, rotate the

action mode changing knob to the

g symbol. Use a bull

point, cold chisel, scaling chisel, etc.

Torque limiter

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

• Bits such as hole saw, which tend to pinch or catch

easily in the hole, are not appropriate for this tool. This

is because they will cause the torque limiter to actuate

too frequently.

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

Hook (Fig. 11)

For Model HR2641

CAUTION:

• Never hook the tool at high location or on potentially

unstable surface.

The hook is convenient for hanging the tool temporarily.

To use the hook, simply lift up hook until it snaps into the

open position.

When not in use, always lower hook until it snaps into the

closed position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side grip (auxiliary handle) (Fig. 12)

CAUTION:

• Always use the side grip to ensure operating safety.

Install the side grip so that the protrusions on the grip fit

in between the grooves on the tool barrel. Then tighten

the grip by turning clockwise at the desired position. It

may be swung 360° so as to be secured at any position.

Bit grease

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5 – 1 g).

This chuck lubrication assures smooth action and longer

service life.

Installing or removing the bit

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 13)

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 14)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out. (Fig. 15)

Bit angle (when chipping, scaling or demolishing)

The bit can be secured at the desired angle. To change

the bit angle, rotate the action mode changing knob to

the O symbol. Turn the bit to the desired angle. (Fig. 16)

Rotate the action mode changing knob to the

g symbol.

(Fig. 17)

Then make sure that the bit is securely held in place by

turning it slightly.

Depth gauge

The depth gauge is convenient for drilling holes of

uniform depth. (Fig. 18)

Press the lock button on the grip base in the direction of

arrow shown in the figure and with the lock button being

pressed insert the depth gauge into the hex. hole in the

grip base. (Fig. 19)

At this time, the depth gauge needs to be inserted so that

its toothed side is directed to the toothed side of hex hole

marking on the grip base as shown in the figure. (Fig. 20)

Adjust the depth gauge to the desired depth by moving it

back and forth while pressing the lock button. After the

adjustment, release the lock button to lock the depth

gauge. (Fig. 21)

NOTE:

• Inserting the depth gauge with its toothed side not

directed to the toothed side of hex hole marking on the

grip base as shown in the figure does not allow the

depth gauge to be locked.

Dust cup (optional accessory) (Fig. 22)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling

operations. Attach the dust cup to the bit as shown in the

figure. The size of bits which the dust cup can be

attached to is as follows.

006406

There is another type of dust cup (optional accessory)

which helps you prevent dust from falling over the tool

and on yourself when performing overhead drilling

operations.

Bit diameter

Dust cup 5 6 mm – 14.5 mm

Dust cup 9 12 mm – 16 mm

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita HR2630T Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info