Handleiding Makita HM 1202 (pagina 7 van 11) (Nederlands, Engels)

78326

Verklein

Vergroot

Pagina terug

1/11

Pagina verder

After installing, always make sure that the bit is

securely held in place by trying to pull it out.

To remove the bit, pull the tool holder cover down all

the way and pull the bit out. (Fig. 4)

Bit angle (Fig. 5)

The bit can be secured at 12 different angles. To

change the bit angle, slide the change ring forward,

then turn the change ring to change the bit angle. At

the desired angle, slide the change ring back to the

original position. The bit will be secured in place.

NOTE:

The change ring cannot turn when the bit is not

installed on the tool.

Side handle (auxiliary handle)

The side handle can be swung 360° on the vertical

and secured at any desired position. It also secures

at eight different positions back and forth on the hori-

zontal. Just loosen the clamp nut to swing the side

handle to a desired position. Then tighten the clamp

nut securely. (Fig. 6)

The side handle also can be mounted in the rear

groove as shown in Fig. 7. Loosen the clamp nut and

widen the side handle base. Slide the side handle

back to the rear groove and secure it with the clamp

nut. (Fig. 7)

Switch action (Fig. 8)

CAUTION:

Before plugging in the tool, always check to see that

the tool is switched off.

To start the tool, push the switch lever on the left side

of the tool. To stop the tool, push the switch lever on

the right side of the tool.

Speed change (Fig. 9)

For HM1202C only

The blows per minute can be adjusted between 950

and 1,900 BPM just by turning the adjusting dial. This

can be done even while the tool is running. The dial is

marked 1 (lowest speed) to 6 (full speed). Refer to

the table below for the relationship between the num-

ber settings on the adjusting dial and the blows per

minute.

Chipping / Scaling / Demolition (Fig. 10)

Hold the tool firmly with both hands. Turn the tool on

and apply slight pressure on the tool so that the tool

will not bounce around, uncontrolled. Pressing very

hard on the tool will not increase the efficiency.

Indicator lamp (Fig. 11)

For HM1202C only

The green power-ON indicator lamp lights up when

the tool is switched ON. If the indicator lamp is lit but

the tool does not start, the carbon brushes may be

worn out, or the electric circuit or the motor may be

defective. If the indicator lamp does not light up and

the tool does not start, the ON/OFF switch or the

mains cord may be defective.

The red service indicator lamp lights up when the

carbon brushes are nearly worn out to indicate that

the tool needs servicing. After approx. 8 hours of use,

the motor will automatically be shut off.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 12 & 13)

Whenever carbon brushes must be replaced, they

cut out the tool automatically. When this occurs,

loosen the screws which secure the rear cover. Pry

up the rear cover with a screwdriver and remove it.

Then replace both carbon brushes at the same time.

Use only identical carbon brushes.

Lubrication

This tool requires no hourly or daily lubrication

because it has a grease-packed lubrication system.

Lubricate the tool every time the carbon brushes are

replaced.

Run the tool for several minutes to warm it up. Switch

off and unplug the tool.

Loosen the six screws and remove the handle.

(Fig. 14)

Remove the crank cap using a socket wrench.

(Fig. 15)

Rest the tool on the table with the bit end pointing

upwards. This will allow the old grease to collect

inside the crank housing. Wipe out the old grease

inside and replace with a fresh grease (30 g). Use

only Makita genuine hammer grease (optional acces-

sory). Filling with more than the specified amount of

grease (approx. 30 g) can cause faulty hammering

action or tool failure. Fill only with the specified

amount of grease. Reinstall the crank cap and tighten

with the socket wrench. (Fig. 16)

CAUTION:

• Be careful not to damage the terminals or lead

wires especially when wiping out the old grease or

installing the handle.

• Do not tighten the crank cap excessively. It is made

of resin and is subject to breakage.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by

a Makita Authorized Service Center.

Number on adjusting dial Blows per minute

6 1,900

5 1,800

4 1,600

3 1,300

2 1,050

1950

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita HM 1202 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Makita HM 1202

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info