Handleiding Makita FS 2300 (pagina 5 van 32) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

448412

Verklein

Vergroot

Pagina terug

1/32

Pagina verder

Lighting up the lamps (Fig. 5)

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger to

turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Reversing switch action (Fig. 6)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

This tool has a reversing switch to change the direction of

rotation. Move the reversing switch lever to the

position (A side) for clockwise rotation or the position

(B side) for counterclockwise rotation.

Hook (Fig. 7)

The hook is convenient for temporarily hanging the tool.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing the bit

To remove the bit, first remove the locator by pulling the

lock ring away from the gear housing. (Fig. 8)

Then check the type of bit holder that your tool employs. If

it has silver colored solid sleeve, it is “magnetic connect

bit holder”. If it has gold and silver colored separate

sleeves, it is “easy-connect bit holder”.

For tool with magnetic bit holder

Grasp the bit with a pair of pliers and pull the bit out of the

magnetic bit holder. Sometimes, it helps to wiggle the bit

with the pliers as you pull.

To install the bit, push it firmly into the magnetic bit holder.

Then install the locator by pushing it firmly back onto the

gear housing. (Fig. 9)

For tool with easy-connect bit holder

Keep fully pushing the slide sleeve, which is a gold

colored part of the easy bit holder, toward the tool and pull

the bit out of the easy bit holder. (Fig. 10 & 11)

To install the bit, push it firmly into the easy bit holder.

Then install the locator by pushing it firmly back onto the

gear housing. (Fig. 12)

Use of locator holder (Fig. 13)

The locator can be temporarily held on the locator holder

during replacing bit or using without locator. To hold the

locator, position the trapezoidal holes of the locator on the

swells of the locator holder and push it in.

OPERATION (Fig. 14)

Fit the screw on the point of the bit and place the point of

the screw on the surface of the workpiece to be fastened.

Apply pressure to the tool and start it. Withdraw the tool

as soon as the clutch cuts in. Then release the switch

trigger.

CAUTION:

• When fitting the screw onto the point of the bit, be

careful not to push in on the screw. If the screw is

pushed in, the clutch will engage and the screw will

rotate suddenly. This could damage a workpiece or

cause an injury.

• Make sure that the bit is inserted straight in the screw

head, or the screw and/or bit may be damaged.

• Hold the tool only by the handle when performing an

operation. Do not touch the metal part.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Phillips Insert bits

• Magnetic bit holder

• Locator

• Easy bit holder

For Model FS2300

For European countries only

Noise

ENG102-2

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 83 dB (A)

Sound power level (L

): 94 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

Vibration

ENG204-2

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: screwdriving without impact

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita FS 2300 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info